Comdial DIGITECH Digital Telephone System Instructions Manual

ANALOG TERMINAL INTERFACE
The Analog Terminal Interface (ATI) device is an optional accessory available for use with the digital telephone system.Connect it to a station port to
lrovide interfacing for such external telephony equipment as an ExecuMail system, an industry-standard model 2500 tone dial telephone, a model 500
‘otary dial telephone, etc.Perform the following programming actions as necessary when operating external equipment through the ATI device.
Press ITCM 3F # 7 4 6 t for base level....

I--Press ITCM ++ # 7 4 6 +k for base level.
‘EATURE DESCRIPTION
lolce Mall Transfer on Busy: When
ZxecuMail is included with the system,
3 busy station may need to be alerted if
he 
ExecuMail system is attempting a
:all transfer to it instead of having the
:all automatically routed to a voice mail
30x. This program feature allows a
station (usually the attendant station) to
oe programmed for this option.
Thru DlallnglATI: Connect external
telephony equipment to a station port
through the Analog Terminal...

II
IPress ITCM +k # 7 4 6 +k for base level.I
FEATURE DESCRIPTIONENTRY CODE AND PROMPTING DISPLAY
Voice Mall Port: Connect the
ExecuMail system or a model 2500
industry-standard telephone to a
station 
port through the Analog
Terminal Interface 
(ATI) device.
Use this programming feature to
enable the station port for ExecuMail
operation (voice mail port). Disable the
station port as a voice mail port when
used for model 2500 telephone
operation.
NOTE: This feature is automatMy
disabled if the ATI device...

TOLL RESTRICTION TABLE CONFIGURATION
Before programming the toll restriction configuration, enter the toll restriction requirements on the programming reference tables found at the end of this
procedure.
In order for toll restriction to take effect, the following three-fold process must occur.
l One or more toll tables must be entered
l Toll tables must be assigned to .all appropriate lines.
l Toll tables must be assigned to all appropriate stations.
After the toll tables are programmed, they must then...

FEATURE DESCRIPTIONENTRY CODE AND PROMPTING DISPLAYREFERENCE RECORD
Base Level: The first step in any
xogramming sequence is to enter the
)ase level. Once in this mode, any
desired configuration can be set.Press 
ITCM Dial t # 7 4 6 +k
system Default: Two toll restriction1. Dial 70.“DEFAULT TOLL ”
:ables are defaulted with
2. Press #to default toll tables.
xe-programmed values and are
xe-assigned to the lines. They need
)nly to be assigned to the stations to put
them into effect. The defaulted tables
zan...

I
P.‘i ITCM +k # 7 4 6 % for base level.I
:EATURE DESCRIPTION
roll Table Entry:
Rsslgn Toll Table To Llne:
ENTRY CODE AND PROMPTING DISPLAY
1. Dial 71.“TOLL TABLE ”
2. Dial 01 - 16 or Press Al - A14, Bl, 82
for toll table 1 - 16.“XXXXX TABLE Y ”
3. Dial 5 or Press Al to establish an allow toll tabk
(Al LED on = allow)“ALLOW TABLE Y 
”
-OR-
Dial 6 or Press A2 to establish a deny toll table,
(A2 LED on = deny)“DENY TABLE Y 
”
4. Dial 1 - 4 or Press A8, A9, AlO, All for entry
number 
1 - 4.wxxxxxx ”
5. Dial...

0d
IPress ITCM % # 7 4 6 $ for base level.I
:EATURE DESCRIPTION
&sign Toll Table To Station
assign Toll Table to be applied when
;ystem is programmed by the attendant
or night transfer of ringing.
ENTRY CODE AND PROMPTING DISPLAY1 REFERENCE RECORD
1. Dial 73.
“ASSIGN TOLL-STA. ”2. Dial 
01 - 16 for toll tables 1-16 to be as’gnd to sta
-OR-Press Al 
- A14, Bl, B2 for tables l-16.
(LED On = Selected table)
3. Dial # to finish entry.
4. Select station ports to be programmed:
- Station 10 - 57: Dial 10 -...

System ProgrammingIMI 66-083
Toll Restriction Programming Reference Tables
[TOLL RESTRICTION
TABLE1I
III101,,1,,,,,,,,,41111111111111TABLE ASSIGNMENT: LINES ALL STATIONS
1 TABLE ASSIGNMENT: LINESSTATIONSI
TOLL RESTRICTION TABLE4
TYPE: ALLOWDENYI
TOLL RESTRICTION TABLE5
TYPE: ALLOWDENY
TOLL RESTRICTION TABLE
6
TYPE: ALLOWDENY1
TOLL RESTRICTION TABLE7
TYPE: ALLOW
DENY
ENTRYENTRY NUMBER 
(16 MAXIMUM)
TOLL RESTRICTION TABLE8
TYPE: ALLOWDENYi
1 ENTRYENTRY NUMBER 116 MAXIMUM\I
III I I
4-62 

IMI 66-083System Pronramrriina ’Toll Restriction Programming Reference Tables 
- continued
TOLL RESTRICTION
TABLE
9TYPE: ALLOW
DENY
ENTRY
ENTRY NUMBER 
116MAXlMUMl
123456709 10 11 12 13 14 15 1
TOLL RESTRICTION TABLE
TYPE: ALLOWDENY
10It ENTRY
ENTRY NUMBER 116 
MAXIMUM1ITOLL RESTRICTION TABLE
12INPE: AUOW
DENYJENTRY
ENTRY NUMBER (16 MAXIMUM)
Ili21314i5l6t7181Q110111112 13 14 15 16
I I I I
TOLL RESTRICTION TABLETYPE: ALLOWDENY14
ENTRY
ENTRY NUMBER (16 MAXIMUM)
1 2 3
4516171619~10~11~12)13~14~15~161IIllTOU...

DATA PRINTER SERVICE
When a data printer is connected to the system, the station message detail record (SMDR) for the system is printed automatically without any
programming or user intervention.
The data printer can also be commanded to print the configuration data for the system.
Partial or complete printouts can be obtained as desired.
When the printer is being used to print the configuration data or SMDA information, SMDR printout is temporarily halted. The SMDR data
collection is continued by the...