Home > Comdial > Communications System > Comdial DIGITECH Digital Telephone System Instructions Manual

Comdial DIGITECH Digital Telephone System Instructions Manual

Here you can view all the pages of manual Comdial DIGITECH Digital Telephone System Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 151

2. If the PC is directly connected to the common
equipment, match the data communications
parameters of the software program to those now
programmed at the telephone system.
-OR-
If remote programming is being employed, the data
parameters of the PC must match the modem
connected to it. The modem 
connected.to the
common equipment must match the data
parameters of it as well.
NOTE: Remember, 
g-bit data is required for XMODEM
protocol.
If the common equipment is not now
programmed to provide 
g-bit data,...

Page 152

?
8
Video Display Terminal OrPersonal Computer
-1 Data JackEquipment Cabinet
Data JackIt
Network Jackr\
crt
Figure 4’3. Remote Programming Block Diagram 

Page 153

IMI 66-083System Programming s
MENU DESCRIPTIONSC.O.S. Programming
1.System C.O.S.
2.Line C.O.S.
3.Station C.O.S.
4. Toll Restriction Table Administration
5.Information
6.Logoff
Enter Selection:MAIN MENU SELECTIONS
l Selection 1: Chooses system COS programming.
l Selection 2: Chooses line COS programming.
l Selection 3: Chooses station COS programming.
l Selection 4: Chooses toil restriction table
administration programming.
l Selection 5: Choses an information menu to
provide assistance with VDT...

Page 154

l Selection 4: Load/Save COS data (on cassette
tape and the transfer of this data through remote
programming)
l Selection 5 : Serial communication parameters (for
data port A and data port B)
l Selection 6: COS data printout
l Selection 7: Set clock date/time.
l Selection 8: SMDA programming (Configures the
Station Message Detailed Accounting feature. Also
refer to page 4-59 for an explaination of call costing
and SMDA reporting.)
lAssign Area Codes / Prefixes to Bands
lEnter band number O-7, enter 0 for...

Page 155

l Selection 2: Line group assignment (assigns line to
line groups, will be reserved 
if the hybrii strap is not
installed)
l Selection 3: Line dialing mode (pulse or tone to
match the connected line)
l Selection 4: Line privacy release (releases privacy
on a line)
0 Selectlon 5: Line toll restriction table assignment
l Selection 6: Line abandoned hold release time
l Selection 7: Set up a line (Using a model line)
(provides a means of programming a group of lines
to match the programming of a model line)...

Page 156

I&Al CcCAri’2Svstem Proaammina
CPX. . . . . . . . . CallPark (l-9)
TGx. . . . . . . . . Line Group (l-4)
VAB. . . . . . . . Voice AnnounceBlock
TGQ . . . . . . . .Line Group Queue
EX.. . . . . . . . . .Exit Button Mapping
System displays list of current key mapping at station.
equipment. Some keys listed may not be present on
the station being programmed.
Enter new function for key and press 
ENTER, or press
ENTER to accept current function.
l Selection 8: Toll restriction administration (assigns
toll...

Page 157

STATION 10 - PROGRAMMING OVERLAY
l Cut out along border.
l Cut out shaded openings.
l Fit over station faceplate.
Al
A0
A210x14
PAOQRNMINQOVERLAYA9
43A10
A4All
A5Al2
A6
A7Al?
All
Bl8283 

Page 158

STATION 10 - PROGRAMMING OVERLAY
l Cut out along border.
l Cut out shaded openings.
l Fit over station faceplate.
92A4
A5
A6
A7
A6
A95x14
Al0PROGRAMMING
OVERLAY
All
3
BlAl2
A19Al‘
B2B3 

Page 159

STATION IO - PROGRAMMING OVERLAY
l Cut out along border.
l Cut out shaded openings.
. Fit over station faceplate.Al
A2A3
A4
A5
A6
A7
PPOl3-100
DIG/TECH(REV I OR HIGHER)
PROGRAMMING
OVERLAYA8
A9
A10
AllA12
Al3
Al4
L
66 B708HOLD 
Bl8283 

Page 160

IMI 66-083
CHAPTER 5
SYSTEM OPERATING PROCEDURES
Systein Operation
SECTION 1STATION OPERATION
ANSWERING CALLS
ANSWERING OUTSIDE CALLS
If the ringing line appears at your telephone,l
Press line button of ringing line (line button with
flashing light).
STATION MONITORING
With station monitoring enabled, a call ringing at a
monitored station can be answered at a monitoring
station.
l Lift handset.l See flashing BLF light, then press DSS button. Light
NOTE: 
If a prime line is assigned and is ringing, or if...
Start reading Comdial DIGITECH Digital Telephone System Instructions Manual

Related Manuals for Comdial DIGITECH Digital Telephone System Instructions Manual

All Comdial manuals