Canon printer PIXMA iP110 User Manual

							Connecting the Printer to the Computer Using a USB CableConnect the printer and the computer using a USB cable as the illustration below. The USB port is located
on the side of the printer.181 
						

							When Detecting the Printers Have the Same Name during SetupWhen the printer is detected during setup, you may see multiple printers of the same name on the detection
result screen.
Select a printer with checking the MAC address or the serial number set to the printer against that on the detection result screen.
Note

						

							Connecting to Other Computer with LAN/Changing the Connection
Method from USB to LAN
To add the computer connecting the printer with LAN or to change the connection method between the
printer and the computer from USB to LAN, perform setup with the Setup CD-ROM or perform it according
to the instructions on our website.
Connecting to Other Computer with LANTo add the computer connecting the printer with LAN, perform setup with the Setup CD-ROM or perform it
according to the instructions on our website.
Changing the Connection Method from USB to LAN
To change the connection method to LAN while you are using the printer with USB connection, perform
setup again with the Setup CD-ROM or perform it again according to the instructions on our website and
select  Change Connection Method .183 
						

							Printing Out Network Setting InformationYou can print out the current network settings of the printer.
Important

						

							Subnet Prefix Length *2Subnet Prefix LengthXXXIPsec *3IPsec settingActiveSecurity Protocol *3Method of the Security ProtocolESP/ESP & AH/AHWPS PIN CODEWPS PIN codeXXXXXXXXWireless LAN DRXDiscontinuous reception
(wireless LAN)Enable/DisableOther SettingsOther settings-Printer NamePrinter namePrinter name (Up to 15 alphanumeric characters)WSDWSD settingEnable/DisableWSD TimeoutTimeout1/5/10/15/20 [min]LPR ProtocolLPR protocol settingEnable/DisableBonjourBonjour settingEnable/DisableBonjour Service NameBonjour service nameBonjour service name (Up to 52 alphanumeric
characters)PictBridge Commun.PictBridge CommunicationEnable/DisableDNS ServerGetting DNS Server
automaticallyAuto/ManualPrimary ServerPrimary server addressXXX.XXX.XXX.XXXSecondary ServerSecondary server addressXXX.XXX.XXX.XXXProxy ServerProxy Server settingEnable/DisableProxy PortSpecifying Proxy Port1 to 65535Proxy AddressProxy AddressXXXXXXXXXXXXXXXXXXXX
("XX" represents alphanumeric characters.)
*1 Depending on the country or region of purchase, one of the channels from 1 to 11 is printed.
*2 Only when IPv6 is enabled, the status of the network is printed.
*3 Only when IPv6 and the IPsec setting are enabled, the status of the network is printed.
185 
						

							About Network Communication
Changing and Confirming Network Settings
Screens for Network Connection of IJ Network Tool
Other Screens of IJ Network Tool
Appendix for Network Communication
186 
						

							Changing and Confirming Network Settings
IJ Network Tool
Changing the Settings in the Wireless LAN Sheet
Changing the WEP Detailed Settings
Changing the WPA/WPA2 Detailed Settings
Changing the Settings in the Wired LAN Sheet
Changing the Settings in the Admin Password Sheet
Monitoring Wireless Network Status
Initializing the Network Settings of the Machine
Viewing the Modified Settings
187 
						

							IJ Network ToolIJ Network Tool is a utility that enables you to display and modify the machine network settings. It is installed
when the machine is set up.
Important

						

							Changing the Settings in the Wireless LAN SheetTo change the wireless network settings of the printer, connect the printer and the computer with a USB
cable temporarily. If you modify the wireless network settings of the computer over wireless connection
without USB connection, your computer may not be able to communicate with the machine after modifying
the settings.
Note

						

							Note