Canon Ir 1600 User Guide
Have a look at the manual Canon Ir 1600 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1335 Canon manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
7-9Finisher-L1 Handling Options 7 NOTE •Copies are stapled in the following places: - When an original is placed on the platen glass: - When originals are placed in the feeder: •If the number of sheets in one set exceeds 15 stapling will not be performed. Only collating will be performed.•If the machine stops during stapling and is displayed, it means that almost all of the staples have been used up and the staple case must be replaced. To proceed, replace the staple case. (See “Replacing the Staple Cartridge in the Stapler Unit-K1,” on p. 7-16.) ■Offset Mode This function outputs paper shifted to the front. IMPORTANT •You can offset A3 , B4 , A4 , A4 , B5 , A5 , 11 x 17 , LGL , LTR , LTR , and STMT . VV ABC Copies are stapled here. Copies are stapled here. ABCABC Copies are stapled here. Copies are stapled here.
Handling Options 7 7-10Finisher-L1 Clearing Paper Jams in the Finisher-L1 If a paper jam occurs when using the finisher, a screen similar to the one shown below appears on the touch panel display. Check where the jam occurred, and follow the procedure described below and the procedure that appears on the touch panel display, to remove the jammed paper. CAUTION •When removing jammed originals or paper, take care not to cut your hands on the edges of the original or paper. •When removing jammed paper or when inspecting the inside of the machine, do not allow necklaces, bracelets, or other metal objects to touch the inside of the machine, as this may result in burns or electrical shock. •When removing paper which has become jammed inside the machine, take care not to allow the toner on the jammed paper to come into contact with your hands or clothing, as this will dirty your hands or clothing. If they become dirty, wash them immediately with cold water. Washing with warm water will set the toner and make it impossible to remove the toner stains. •When removing paper which has become jammed inside the machine, remove the jammed paper gently to prevent the toner on the paper from scattering and entering your eyes or mouth. If toner enters your eyes or mouth, wash them immediately with cold water and consult a physician. 1Open the front cover. OPEN THE FRONT COVER REC. PAPER JAM
7-11Finisher-L1 Handling Options 7 2If you see the jammed paper, remove it. If you cannot remove it, go to step 3. 3Open the stack bypass. 4Pull out the left cover. CAUTION •Grasp the handle and pull out the left cover horizontally to the left. (Be careful not to pull it upward as it may easily come off.)
Handling Options 7 7-12Finisher-L1 5Open the upper left cover. 6If you see any jammed paper, remove it. If you cannot remove it, go to step 7. CAUTION •Be careful not to touch inside the machine because some parts get very hot. 7Holding the green knob, lift the inner guide.
7-13Finisher-L1 Handling Options 7 8Remove any jammed paper under the inner guide. CAUTION •Be careful not to touch inside the machine because some parts get very hot. 9Close the upper left cover. CAUTION •When closing the cover, be careful not to get your fingers caught, as this may result in personal injury.
Handling Options 7 7-14Finisher-L1 10Close the left cover. CAUTION •Close the left cover until it latches. •When closing the cover, be careful not to get your fingers caught, as this may result in personal injury. 11Close the stack bypass. CAUTION •When closing the stack bypass, be careful not to get your fingers caught, as this may result in personal injury.
7-15Finisher-L1 Handling Options 7 12Close the front cover. CAUTION •When closing the cover, be careful not to get your fingers caught, as this may result in personal injury.
Handling Options 7 7-16Finisher-L1 Replacing the Staple Cartridge in the Stapler Unit-K1 When the finisher is almost out of staples and the staple cartridge must be replaced, the following display appears. Follow the procedure described below to replace the staple cartridge. 1Open the front cover of the finisher. 2Pull out the staple cartridge, holding the tab as illustrated below. LOAD STAPLES Hold here to pull out the cartridge.
7-17Finisher-L1 Handling Options 7 3Insert the new staple cartridge. IMPORTANT •Use only the special staple cartridge intended for use with this machine. NOTE •Only one staple cartridge can be inserted at a time. 4Close the front cover of the finisher. CAUTION •When closing the cover, be careful not to get your fingers caught, as this may result in personal injury.
Handling Options 7 7-18Finisher-L1 Removing Jammed Staples from the Stapler Unit-K1 If the machine does not staple even though you have set the staple mode, a staple jam may have occurred in the Stapler Unit-K1. Check the staple cartridge and remove jammed staples if necessary. 1Open the front cover of the finisher. 2Pull out the staple cartridge, holding the tab as illustrated below. Hold here to pull out the cartridge.