Home > Belkin > Router > Belkin Router F5D8231-4 User Manual

Belkin Router F5D8231-4 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Belkin Router F5D8231-4 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 19 Belkin manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 623
    							
    3029
    Alternate  Setup  Method
    
    3029
    Alternate  Setup  Method
    
    Setting your Internet Service Provider (ISP) Connection 
    Type to Dynamic IP 
    A dynamic connection type is the most common connection type found with 
    cable modems. Setting the connection type to “dynamic” in many cases is 
    enough to complete the connection to your ISP. Some dynamic connection 
    types may require a host name. You can enter your host name in the space 
    provided if you were assigned one. Your host name is assigned by your ISP. 
    Some dynamic connections may require that you clone the MAC address of 
    the PC that was originally connected to the modem.
    1.  Host Name 
    This  space  is  provided  to  enter  a  host  name  that  needs  to  be 
    visible  to  your  ISP.  Enter  your  host  name  here  and  click  “Apply 
    Changes” 
    (3).  If  your  ISP  did  not  assign  you  a  host  name,  or  you 
    are  not  sure,  leave  this  blank.
    2.   Change WAN MAC Address 
    If  your  ISP  requires  a  specific  MAC  address  to  connect  to  the 
    service,  you  can  enter  a  specific  MAC  address  or  clone  the 
    current  computer’s  MAC  address  through  this  link.
     
    (2)
    (1) 
    						
    							
    30
    
    Alternate  Setup  Method
    30
    s e c t i o n
    2
    1
    3
    4
    5
    6
    7
    8
    9
    10
    
    Setting your Internet Service Provider (ISP) Connection Type to Static IP 
    A  static  IP  address  connection  type  is  less  common  than  other 
    connection  types.  If  your  ISP  uses  static  IP  addressing,  you  will 
    need  your  IP  address,  subnet  mask,  and  ISP  gateway  address.  This 
    information  is  available  from  your  ISP  or  on  the  paperwork  that 
    your  ISP  left  with  you.  Type  in  your  information,  then  click  “Apply 
    Changes” 
    (5).  After  you  apply  the  changes,  the  Internet  Status 
    indicator  will  read  “connection  OK”  if  your  Router  is  set  up  properly.
    1.  IP Address 
    Provided  by  your  ISP.  Enter  your  IP  address  here.
    2.   Subnet Mask 
    Provided  by  your  ISP.  Enter  your  subnet  mask  here.
    3.  ISP Gateway Address 
    Provided  by  your  ISP.  Enter  the  ISP  gateway  address  here.
    4.   My ISP Provides More Than One Static IP Address 
    If  your  ISP  assigns  you  more  than  one  static  IP  address,  your 
    Router  is  capable  of  handling  up  to  five  static  WAN  IP  addresses. 
    Select  “My  ISP  provides  more  than  one  static  IP  address”  and 
    enter  your  additional  addresses.
     
    (1)(2)(3)(4)
    (5) 
    						
    							
    3231
    Alternate  Setup  Method
    
    3231
    Alternate  Setup  Method
    
    Setting your ISP Connection Type to PPPoE 
    Most  DSL  providers  use  PPPoE  as  the  connection  type.  If  you  use  a 
    DSL  modem  to  connect  to  the  Internet,  your  ISP  may  use  PPPoE  to 
    log  you  into  the  service.  If  you  have  an  Internet  connection  in  your 
    home  or  small  office  that  doesn’t  require  a  modem,  you  may  also
     
    use  PPPoE.
    Your  connection  type  is  PPPoE  if:
    1)    Your  ISP  gave  you  a  user  name  and  password,  which  is  required 
    to  connect  to  the  Internet.
    2)    Your  ISP  gave  you  software  such  as  WinPOET  or  Enternet300 
    that  you  use  to  connect  to  the  Internet.
    3)    You  have  to  double-click  on  a  desktop  icon  other  than  your 
    browser  to  get  on  the  Internet. 
    						
    							
    32
    
    Alternate  Setup  Method
    32
    s e c t i o n
    2
    1
    3
    4
    5
    6
    7
    8
    9
    10
    
     
    1.  User Name 
    This  space  is  provided  to  type  in  your  user  name  that  was 
    assigned  by  your  ISP.
    2.   Password 
    Type  in  your  password  and  retype  it  into  the  “Retype  Password” 
    box  to  confirm  it.
    3.  Service Name 
    A  service  name  is  rarely  required  by  an  ISP.  If  you  are  not  sure  if 
    your  ISP  requires  a  service  name,  leave  this  blank.
    4.   MTU 
    The  MTU  setting  should  never  be  changed  unless  your  ISP  gives 
    you  a  specific  MTU  setting.  Making  changes  to  the  MTU  setting 
    can  cause  problems  with  your  Internet  connection  including 
    disconnection  from  the  Internet,  slow  Internet  access,  and 
    problems  with  Internet  applications  working  properly.
    5.  Disconnect after X... 
    The  “Disconnect”  feature  is  used  to  automatically  disconnect  the 
    Router  from  your  ISP  when  there  is  no  activity  for  a  specified 
    period  of  time.  For  instance,  placing  a  check  mark  next  to  this 
    option  and  entering  “5”  into  the  minute  field  will  cause  the  Router 
    to  disconnect  from  the  Internet  after  five  minutes  of  no  Internet 
    activity.  This  option  should  be  used  if  you  pay  for  your  Internet 
    service  by  the  minute.
    (1)(2)
    (3)(4)
    (5) 
    						
    							
    3433
    Alternate  Setup  Method
    
    3433
    Alternate  Setup  Method
    
    Setting your Internet Service Provider (ISP) Connection Type to 
    Point-to-Point Tunneling Protocol (PPTP)
     
    [European Countries Only].
     
    Some  ISPs  require  a  connection  using  PPTP  protocol,  a  type  of 
    connection  most  common  in  European  countries.  This  sets  up  a  direct 
    connection  to  the  ISP’s  system.  Type  in  the  information  provided 
    by  your  ISP  in  the  space  provided.  When  you  have  finished,  click 
    “Apply  Changes” 
    (9).  After  you  apply  the  changes,  the  Internet  Status 
    indicator  will  read  “connection  OK”  if  your  Router  is  set  up  properly.
     
    1.   PPTP Account 
    Provided  by  your  ISP.  Enter  your  PPTP  account  name  here.
    2.  PPTP Password 
    Type  in  your  password  and  retype  it  into  the  “Retype  Password” 
    box  to  confirm  it.
    3.  Host Name 
    Provided  by  your  ISP.  Enter  your  host  name  here.
    4.   Service IP Address 
    Provided  by  your  ISP.  Enter  your  service  IP  address  here.
    5.  My IP Address 
    Provided  by  your  ISP.  Enter  the  IP  address  here.
    (1)
    (2)
    (4)
    (5)
    (7)
    (3)
    (6)
    (8)
    (9) 
    						
    							
    34
    
    Alternate  Setup  Method
    34
    s e c t i o n
    2
    1
    3
    4
    5
    6
    7
    8
    9
    10
    
    6.  My Subnet Mask 
    Provided  by  your  ISP.  Enter  the  IP  address  here.
    7.   Connection ID (optional) 
    Provided  by  your  ISP.  If  your  ISP  did  not  give  you  a  connection 
    ID,  leave  this  blank.
    8.  Disconnect after X.... 
    The  “Disconnect”  feature  is  used  to  automatically  disconnect  the 
    Router  from  your  ISP  when  there  is  no  activity  for  a  specified 
    period  of  time.  For  instance,  placing  a  check  mark  next  to  this 
    option  and  entering  “5”  into  the  minute  field  will  cause  the  Router 
    to  disconnect  from  the  Internet  after  five  minutes  of  no  Internet 
    activity.  This  option  should  be  used  if  you  pay  for  your  Internet 
    service  by  the  minute. 
    						
    							
    3635
    Alternate  Setup  Method
    
    3635
    Alternate  Setup  Method
    
    Setting your Connection Type if you are a Telstra® BigPond User 
    [Australia  Only].  Your  user  name  and  password  are  provided  to  you  by 
    Telstra  BigPond.  Enter  this  information  below.  Choosing  your  state 
    from  the  drop-down  menu 
    (1)  will  automatically  fill  in  your  login  server 
    IP  address.  If  your  login  server  address  is  different  than  one  provided 
    here,  you  may  manually  enter  the  login  server  IP  address  by  placing  a 
    check  in  the  box  next  to  “User  decide  login  server  manually” 
    (4)  and 
    type  in  the  address  next  to  “Login  Server” 
    (5).  When  you  have  entered 
    all  of  your  information,  click  “Apply  Changes” 
    (6).  After  you  apply  the 
    changes,  the  Internet  Status  indicator  will  read  “connection  OK”  if 
    your  Router  is  set  up  properly.
    1.  Select your State 
    Select  your  state  from  the  drop-down  menu (1).  The  “Login 
    Server”  box  will  automatically  be  filled  in  with  an  IP  address. 
    If  for  some  reason  this  address  does  not  match  the  address 
    that  Telstra  has  given,  you  can  manually  enter  the  login  server 
    address.  See  “User  decide  login  server  manually” 
    (4).
    2.  User Name 
    Provided  by  your  ISP.  Type  in  your  user  name  here.
    3.   Password 
    Type  in  your  password  and  retype  it  into  the  “Retype  Password” 
    box  to  confirm  it.
    (1)
    (2)
    (4)
    (5)
    (3)
    (6) 
    						
    							
    36
    
    Alternate  Setup  Method
    36
    s e c t i o n
    2
    1
    3
    4
    5
    6
    7
    8
    9
    10
    
    4.   User Decide Login Server Manually 
    If  your  login  server  IP  address  is  not  available  in  the  “Select  Your 
    State”  drop-down  menu 
    (1),  you  may  manually  enter  the  login 
    server  IP  address  by  placing  a  check  in  the  box  next  to  “User 
    decide  login  server  manually”  and  type  in  the  address  next  to 
    “Login  Server” 
    (5).
    Setting Custom Domain Name Server (DNS) Settings 
    A  “Domain  Name  Server”  is  a  server  located  on  the  Internet  that 
    translates  Universal  Resource  Locaters  (URLs)  like  “www.belkin.com”
     
    to  IP  addresses.  Many  Internet  Service  Providers  (ISPs)  do  not  require 
    you  to  enter  this  information  into  the  Router.  The  “Automatic  from
     
    ISP”  box 
    (1)  should  be  checked  if  your  ISP  did  not  give  you  a  specific 
    DNS  address.  If  you  are  using  a  static  IP  connection  type,  then  you  may 
    need  to  enter  a  specific  DNS  address  and  secondary  DNS  address  for 
    your  connection  to  work  properly.  If  your  connection  type  is  dynamic  or 
    PPPoE,  it  is  likely  that  you  do  not  have  to  enter  a  DNS  address.  Leave 
    the  “Automatic  from  ISP”  box  checked.  To  enter  the  DNS  address 
    settings,  uncheck  the  “Automatic  from  ISP”  box  and  enter  your  DNS 
    entries  in  the  spaces  provided.  Click  “Apply  Changes” 
    (2)  to  save 
    the  settings.
    (1)
    (2) 
    						
    							
    Configuring your WAN Media Access Controller (MAC) Address 
    All  network  components  including  cards,  adapters,  and  routers,  have 
    a  unique  “serial  number”  called  a  MAC  address.  Your  Internet  Service 
    Provider  (ISP)  may  record  the  MAC  address  of  your  computer’s  adapter 
    and  only  let  that  particular  computer  connect  to  the  Internet  service. 
    When  you  install  the  Router,  its  own  MAC  address  will  be  “seen”  by  the 
    ISP  and  may  cause  the  connection  not  to  work.  Belkin  has  provided  the 
    ability  to  clone  (copy)  the  MAC  address  of  the  computer  into  the  Router. 
    This  MAC  address,  in  turn,  will  be  seen  by  the  ISP’s  system  as  the 
    original  MAC  address  and  will  allow  the  connection  to  work.  If  you  are 
    not  sure  whether  your  ISP  needs  to  see  the  original  MAC  address,
     
    simply  clone  the  MAC  address  of  the  computer  that  was  originally 
    connected  to  the  modem.  Cloning  the  address  will  not  cause  any 
    problems  with  your  network.
    Cloning your MAC Address 
    To  clone  your  MAC  address,  make  sure  that  you  are  using  the  computer 
    that  was  ORIGINALLY  CONNECTED  to  your  modem  before  the  Router 
    was  installed.  Click  the  “Clone”  button 
    (1).  Click  “Apply  Changes” (3). 
    Your  MAC  address  is  now  cloned  to  the  Router.
    Entering a Specific MAC Address 
    In  certain  circumstances  you  may  need  a  specific  WAN  MAC  address. 
    You  can  manually  enter  one  in  the  “MAC  Address”  page.  Type  in  a  MAC 
    address  in  the  spaces  provided 
    (2)  and  click  “Apply  Changes” (3)  to 
    save  the  changes.  The  Router’s  WAN  MAC  address  will  now  be  changed 
    to  the  MAC  address  you  specified.
    37
    Alternate  Setup  Method
    38
    (1)
    (3)
    (2) 
    						
    							
    Using  your  Internet  browser,  you  can  access  the  Router’s  Web-Based 
    Advanced  User  Interface.  In  your  browser,  type  “192.168.2.1”  (do  not 
    type  in  anything  else  such  as  “http://”  or  “www”)  then  press  the
     
    “Enter”  key.
    You  will  see  the  Router’s  home  page  in  your  browser  window.
    Viewing the LAN Settings 
    Clicking  on  the  header  of  the  LAN  tab 
    (1)  will  take  you  to  the  LAN  tab’s 
    header  page.  A  quick  description  of  the  functions  can  be  found  here.  To 
    view  the  settings  or  make  changes  to  any  of  the  LAN  settings,  click  on 
    “LAN  Settings” 
    (2)  or  to  view  the  list  of  connected  computers,  click  on 
    “DHCP  client  list” 
    (3).
    Using the Web-Based Advanced User Interface
    s e c t i o n
    2
    1
    3
    4
    5
    6
    7
    8
    9
    10
    38
    (1)
    (2)
    (3) 
    						
    All Belkin manuals Comments (0)

    Related Manuals for Belkin Router F5D8231-4 User Manual