Apple macbook pro 17 inch mid 2010 User Manual
Have a look at the manual Apple macbook pro 17 inch mid 2010 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
MacBook Pro (17-inch, Mid 2010) Take Apart — Trackpad 191 2010-06-11 9 Fold sticky notes over so that top case can be laid flat. 10 Tighten 6 short Phillips #000 screws at flexures. 11 Inspect that gaps between trackpad and top case are even on all sides. If not, loosen screws and adjust.
MacBook Pro (17-inch, Mid 2010) Take Apart — Trackpad 192 2010-06-11 12 Insert tri-lobe #0 set screw. 13 Slowly turn set screw in small increments until trackpad has a normal clicking motion. Important: Do not overtighten set screw or you may damage trackpad. 14 Adhere flex cable to mounting ramp.
MacBook Pro (17-inch, Mid 2010) Take Apart — MagSafe Board 193 2010-06-11 First Steps Remove: • Bottom case • Memory • Fans • Logic board Before you begin this procedure, disconnect the battery from the logic board. Failure to do so could damage the computer. MagSafe Board
MacBook Pro (17-inch, Mid 2010) Take Apart — MagSafe Board 194 2010-06-11 Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Phillips #00 screwdriver Removal Note: Although logic board is pictured here in relation to MagSafe board, the logic board would already be removed. 1 Remove 2 (7.6-mm) 922-8929 screws. 2 Lift out MagSafe board.
MacBook Pro (17-inch, Mid 2010) Take Apart — MagSafe Board 195 2010-06-11 Replacement Caution: Plug in a disconnected adapter cable. 1 Making sure power is cut off, install MagSafe board screws. 2 Test port alignment by plugging in power cable from 4 angles. • If port is off center and cable does not seat securely, loosen MagSafe screws, realign port with cable in place, and secure screws. • If port seats correctly, continue. 3 Connect MagSafe cable to logic board. 4 Install logic board and remaining parts. 5 With computer fully assembled, test power with power cable.
MacBook Pro (17-inch, Mid 2010) Take Apart — Heatsink 196 2010-06-11 First Steps Remove: • Bottom case • Memory • Fans • Logic board Before you begin this procedure, disconnect the battery from the logic board. Failure to do so could damage the computer. Heatsink
MacBook Pro (17-inch, Mid 2010) Take Apart — Heatsink 197 2010-06-11 Tools • Clean, soft, lint-free cloth • ESD wrist strap and mat • Magnetized Phillips #0 or #1 screwdriver • Thermal grease syringe • Alcohol pads • Black stick Removal Caution: Hold heatsink by edges, not by the heat pipes: 1 Remove 6 (8.35-mm) screws. Note: Screws are in heatsink kit and are not offered separately.
MacBook Pro (17-inch, Mid 2010) Take Apart — Heatsink 198 2010-06-11 2 Keeping heatsink parallel to logic board, gently wiggle the heatsink to loosen the bond to the board. 3 With a black stick, scrape off thermal grease and use alcohol pad to clean thermal pads and chips.
MacBook Pro (17-inch, Mid 2010) Take Apart — Heatsink 199 2010-06-11 Replacement Important: New heatsinks include pre-applied thermal grease. Follow steps 1-2 only if re- installing the original heatsink. 1 Caution: The syringe contains enough thermal grease for 3 chips. Use a pen to mark the syringe in thirds. 2 Inject 1/3 of grease on the center of each chip 3 Lower the heatsink over the logic board.
MacBook Pro (17-inch, Mid 2010) Take Apart — Heatsink 200 2010-06-11 4 Install heatsink screws in order, 1/2 way first, then tighten the rest of the way.