1991 1999 ford explorer chilton User Manual
Have a look at the manual 1991 1999 ford explorer chilton User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 41 Ford manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Install the bulb into the lamp socket. Follow the warning above. 7. Position the lamp socket into the lens and install the retaining clip. 8. Reposition the rubber boot. 9. Connect the electrical harness plug and position the lens assembly into the lamp housing. 10. Engage the lens retaining tab. Ensure that the lens is securely held in the lamp housing. 11. Check the light for proper operation. 12. Chilton® Automotive Information Systems. © 2004 Thomson Delmar Learning. HOW TO USE THIS BOOK REMOVAL & INSTALLATION 737
TRAILER WIRING Wiring the vehicle for towing is fairly easy. There are a number of good wiring kits available and these should be used, rather than trying to design your own. All trailers will need brake lights and turn signals as well as tail lights and side marker lights. Most areas require extra marker lights for overwide trailers. Also, most areas have recently required back-up lights for trailers, and most trailer manufacturers have been building trailers with back-up lights for several years. Additionally, some Class I, most Class II and just about all Class III trailers will have electric brakes. Add to this number an accessories wire, to operate trailer internal equipment or to charge the trailers battery, and you can have as many as seven wires in the harness. Determine the equipment on your trailer and buy the wiring kit necessary. The kit will contain all the wires needed, plus a plug adapter set which includes the female plug, mounted on the bumper or hitch, and the male plug, wired into, or plugged into the trailer harness. When installing the kit, follow the manufacturers instructions. The color coding of the wires is usually standard throughout the industry. One point to note: some domestic vehicles, and most imported vehicles, have separate turn signals. On most domestic vehicles, the brake lights and rear turn signals operate with the same bulb. For those vehicles with separate turn signals, you can purchase an isolation unit so that the brake lights wont blink whenever the turn signals are operated, or, you can go to your local electronics supply house and buy four diodes to wire in series with the brake and turn signal bulbs. Diodes will isolate the brake and turn signals. The choice is yours. The isolation units are simple and quick to install, but far more expensive than the diodes. The diodes, however, require more work to install properly, since they require the cutting of each bulbs wire and soldering in place of the diode. One, final point, the best kits are those with a spring loaded cover on the vehicle mounted socket. This cover prevents dirt and moisture from corroding the terminals. Never let the vehicle socket hang loosely; always mount it securely to the bumper or hitch. Chilton® Automotive Information Systems. © 2004 Thomson Delmar Learning. TRAILER WIRING 739
CIRCUIT PROTECTION Fuses Fuse panel and identification for 1991-94 Ranger modelsClick to enlarge CIRCUIT PROTECTION 741
Fuse panel and identification for 1991-94 Explorer models Click to enlarge HOW TO USE THIS BOOK 742 Fuses
Fuse panel and power distribution box identification for 1995-99 Ranger models-Part 1 Click to enlarge HOW TO USE THIS BOOK Fuses 743
Fuse panel and power distribution box identification for 1995-99 Ranger models-Part 2 Click to enlarge HOW TO USE THIS BOOK 744 Fuses
Fuse panel and power distribution box identification for 1995-99 Ranger models-Part 3 Click to enlarge HOW TO USE THIS BOOK Fuses 745
Fuse panel and power distribution box identification for 1995-99 Explorer/Mountaineer models-Part 1 Click to enlarge HOW TO USE THIS BOOK 746 Fuses
Fuse panel and power distribution box identification for 1995-99 Explorer/Mountaineer models-Part 2 Click to enlarge HOW TO USE THIS BOOK Fuses 747
Fuse panel and power distribution box identification for 1995-99 Explorer/Mountaineer models-Part 3 Click to enlarge REPLACEMENT Fuse Panel Located inside the passenger compartment, under the drivers-side of the instrument panel. Turn the ignition switch OFF. 1. HOW TO USE THIS BOOK 748 REPLACEMENT