Yamaha Dvx 1000 Owners Manual

Pro Tools Remote Layer231
DM1000 Version 2—Owner’s Manual
Remote Control
17
6Move the cursor to a parameter control, then rotate the Parameter wheel 
or press the [ENTER] button to adjust the value.
One or two parameters are assigned to a single parameter control. To turn the parameter 
setting on or off, press [ENTER]. To modify the parameter variable, rotate the Parameter 
wheel.
7When you finish adjusting the parameters, move the cursor to the PARAM 
button, then press [ENTER] to switch it to INSERT....

232Chapter 17—Remote Control
DM1000 Version 2—Owner’s Manual
Scrub & Shuttle
By assigning the DAW SCRUB parameter to one of the User Defined buttons [1]–[12], you 
can scrub Pro Tools tracks back and forth by turning the Parameter wheel. By assigning the 
DAW SHUTTLE parameter to one of the User Defined buttons [1]–[12], you can shuttle 
back and forth by turning the Parameter wheel.
1Assign the DAW SCRUB or DAW SHUTTLE parameter to one of the User 
Defined buttons [1]–[12].
Before assigning parameters to...

Pro Tools Remote Layer233
DM1000 Version 2—Owner’s Manual
Remote Control
17
Automation
You can view the Pro Tools Automation mode as follows:
1Press the [F3] or [F4] button to display the channels for remote control.
2Press the DISPLAY ACCESS [AUTOMIX] button.
The channel’s Automation settings are displayed.
While the STEREO [AUTO] button is on, the channel [SEL] button indicators also display 
the channel’s Automation mode.
Pro Tools Display [SEL] Button Indicators
Auto write
Wrt
Flashing red (Record...

234Chapter 17—Remote Control
DM1000 Version 2—Owner’s Manual
Using the Panner
■Selecting a Track
Use the SELECTED CHANNEL ROUTING buttons to manipulate the following track 
operations.
■Stereo Track Link
You can control the panner for the L and R channels of stereo tracks simultaneously or indi-
vidually, depending on the stereo link status.
To cancel the stereo panner link, press and hold down the [Control] key on the keyboard 
and move the Joystick.
■Panner Operation via the Joystick
1Select the track...

Nuendo/Cubase SX Remote Layer235
DM1000 Version 2—Owner’s Manual
Remote Control
17
Nuendo/Cubase SX Remote Layer
You can remotely control Nuendo and Cubase SX using Remote Layers 1 and 2.
■Configuring Computers
1Connect the DM1000 to your computer using a USB cable, and install the 
required USB driver included on the DM1000 CD-ROM.
Refer to the Studio Manager installation guide for more information on installing the 
driver.
2Launch Nuendo/Cubase SX, select the Device Setup menu, and set up...

236Chapter 17—Remote Control
DM1000 Version 2—Owner’s Manual
MIDI Remote Layer
If you select USER DEFINED as the target for Remote Layer 1 or 2, you can remotely control 
the parameters of external MIDI devices (such as synthesizers and tone generators) by oper-
ating the channel Encoders, [ON] buttons, and faders to output various MIDI messages. 
(This is called MIDI Remote function.) 
You can store MIDI messages assigned to the channel controls in four banks. When the 
DM1000 is shipped from the...

MIDI Remote Layer237
DM1000 Version 2—Owner’s Manual
Remote Control
17
2Press the DISPLAY ACCESS [SETUP] button repeatedly until the Setup | 
MIDI/Host page appears.
3Move the cursor to the REMOTE 2 parameter box (
1) in the SPECIAL FUNC-
TIONS section, rotate the Parameter wheel to select MIDI, then press 
[ENTER].
If the MIDI port is already in use, a confirmation window for changing the assignment 
appears. Move the cursor to the YES button, then press [ENTER].
4Press the DISPLAY ACCESS [REMOTE]...

238Chapter 17—Remote Control
DM1000 Version 2—Owner’s Manual
DID, SHORT, LONG
These parameters display the channel names. The ID parameter displays the channel ID 
(RM01–RM16) for the currently-controlled MIDI device.
EON section
This section displays the type of MIDI messages (in hexadecimal or alphabet) assigned 
to the [ON] buttons for the currently-selected channels (RM01–RM16).
•LATCH/UNLATCH..... This button toggles between Latch and Unlatch for [ON] but-
ton operation....

MIDI Remote Layer239
DM1000 Version 2—Owner’s Manual
Remote Control
17
Assigning MIDI Messages to Channel Controls
You can quickly use the MIDI Remote function if you use the factory presets in the banks. 
However, you can also assign the desired MIDI messages to the faders, [ON] buttons, or 
Encoders.
This section describes how to assign MIDI messages to the channel controls, using the 
example of assigning Hold On/Off messages (Control Change #64; Values 127 & 0) to the 
Channel 1 [ON] button.
1Connect...

240Chapter 17—Remote Control
DM1000 Version 2—Owner’s Manual
6Press and hold down the MIDI keyboard foot switch.
The MIDI Hold On message is assigned in the DATA parameter box.
MIDI messages are described below:
•00–7F............................. MIDI messages are expressed in hexadecimal.
•END............................... This message indicates the end of MIDI messages. Subsequent 
messages assigned in the DATA parameter boxes will be 
ignored.
•–...................................... This message...