Yamaha Dvx 1000 Owners Manual
Here you can view all the pages of manual Yamaha Dvx 1000 Owners Manual. The Yamaha manuals for Home Theater System are available online for free. You can easily download all the documents as PDF.
Page 251
Assigning Parameters to Control Changes for Real-time Control251 DM1000 Version 2—Owner’s Manual MIDI 18 4Move the cursor to the MODE parameter’s TABLE button (1), then press [ENTER]. The MODE parameter determines which MIDI messages are transmitted when DM1000 parameters are adjusted. The following options are available for the MODE parameter: •TABLE............................ MIDI Control Change messages are transmitted in accordance with the assignments on this page....
Page 252
252Chapter 18—MIDI DM1000 Version 2—Owner’s Manual ONCHANNEL INPUT1–48 MASTER BUS1–8/AUX1–8/STEREO AUX1 SEND INPUT1–48 AUX2 SEND AUX3 SEND AUX4 SEND AUX5 SEND AUX6 SEND AUX7 SEND AUX8 SEND BUS TO ST BUS1–8 PHASE CHANNEL INPUT1–48 INSERT ONCHANNEL INPUT1–48 MASTER BUS1–8/AUX1–8/STEREO PRE/POSTAUX1 SEND INPUT1–48 AUX2 SEND AUX3 SEND AUX4 SEND AUX5 SEND AUX6 SEND AUX7 SEND AUX8 SEND IN DELAYON INPUT1–48 TIME HIGH TIME MID TIME LOW MIX HIGH MIX LOW FB GAIN H FB GAIN L OUT DELAYON BUS1–8/AUX1–8/STEREO L, R...
Page 253
Assigning Parameters to Control Changes for Real-time Control253 DM1000 Version 2—Owner’s Manual MIDI 18 EQON INPUT1–48/BUS1–8/AUX1–8/STEREO Q LOW F LOW G LOW H G LOW L Q LO-MID F LO-MID G LO-MID H G LO-MID L Q HI-MID F HI-MID G HI-MID H G HI-MID L Q HIGH F HIGH G HIGH H G HIGH L ATT H ATT L HPF ON LPF ON GATEON INPUT1–48 AT TA C K THRESH H THRESH L RANGE HOLD H HOLD L DECAY H DECAY L COMPON INPUT1–48/BUS1–8/AUX1–8/STEREO AT TA C K THRESH H THRESH L RELEASE H RELEASE L RATIO GAIN H GAIN L KNEE PA...
Page 254
254Chapter 18—MIDI DM1000 Version 2—Owner’s Manual Parameters that feature a setting range of more than 128 steps (such as Fader and Delay Time parameters) require two or more Control Change messages to specify the values. For example, if you wish to control Fader parameters on certain channels using Control Changes, you must assign the same channel to two Control Change numbers, and select “FADER H” and “FADER L” for the Control Changes in the parameter boxes in the first PARAMETER column....
Page 255
Assigning Parameters to Control Changes for Real-time Control255 DM1000 Version 2—Owner’s Manual MIDI 18 If you wish to control Delay Time parameters on certain channels using Control Changes, you must assign the same channel Delay parameter to three Control Change numbers, and select “TIME LOW,” “TIME MID,” and “TIME HIGH” for the Control Changes in the parameter boxes in the second (middle) PARAMETER column. 7Press the DISPLAY ACCESS [MIDI] button repeatedly until the MIDI | Setup page appears,...
Page 256
256Chapter 18—MIDI DM1000 Version 2—Owner’s Manual Controlling Parameters by Using Parameter Changes You can control DM1000 parameters in real time by using Parameter Change messages that are System Exclusive messages, instead of using MIDI Control Changes. See “MIDI Data Format” at the end of this Manual for detailed information on available Parameter Changes. 1Press the DISPLAY ACCESS [SETUP] button repeatedly until the Setup | MIDI/Host page appears, then specify ports for transmission and...
Page 257
Transmitting Parameter Settings via MIDI (Bulk Dump)257 DM1000 Version 2—Owner’s Manual MIDI 18 The MIDI | Bulk page appears. The page includes the following parameters: ACATEGORY section This section enables you to select data for transmission and reception. BREQUEST Move the cursor to this button, then press [ENTER] to transmit messages from the DM1000 that request a second DM1000 (connected to the first DM1000) to transmit the data specified in the CATEGORY section. This button is used primarily when...
Page 258
258Chapter 18—MIDI DM1000 Version 2—Owner’s Manual •SETUPMEM................. This button selects the DM1000 setup data (i.e., system set- tings). •PGM TABLE................. This button selects the MIDI | Pgm Asgn page settings. •CTL TABLE................... This button selects the MIDI | Ctl Asgn page settings. •PLUG-IN....................... This button selects the settings of any optional Y56K cards installed in Slot #1 or #2. You can select Y56K card programs in the parameter box next to the...
Page 259
Controlling the DM1000 from a Video Editor259 DM1000 Version 2—Owner’s Manual Controlling the DM1000 from a Video Editor 19 19 Controlling the DM1000 from a Video Editor This chapter describes the control functions, which enable you to control the DM1000 from a video editor using the ESAM protocol. About ESAM ESAM (Editing Suite Audio Mixers) is the post-production standards for linking video edi- tor to a mixing console. You can automate audio crossfade and switching operations that are linked to...
Page 260
260Chapter 19—Controlling the DM1000 from a Video Editor DM1000 Version 2—Owner’s Manual Crossfade via ESAM Commands This section describes how to execute a crossfade (transition) using the DM1000’s ESAM mode. 1Press the DISPLAY ACCESS [SETUP] button repeatedly until the Setup | Remote page appears. 2Move the cursor to the REMOTE FUNCTION parameter, then select ESAM to enter ESAM mode. A confirmation message appears. Move the cursor to the YES button, then press [ENTER] to confirm. 3Move the cursor to...