Yamaha Dvx 1000 Owners Manual
Here you can view all the pages of manual Yamaha Dvx 1000 Owners Manual. The Yamaha manuals for Home Theater System are available online for free. You can easily download all the documents as PDF.
Page 201
Automix Main Page201 DM1000 Version 2—Owner’s Manual Automix 16 When the TO END button is on, the way in which fader events are processed depends on the currently-selected Fader Edit mode and Edit Out mode. The following table shows how the faders operate when the Fader Edit mode is set to Absolute. If the Fader Edit mode is set to Relative, and the Edit Out mode is set to either Takeover or Off, the fader will remain at a position relative to its position when recording was stopped right through to...
Page 202
202Chapter 16—Automix DM1000 Version 2—Owner’s Manual The following table shows how faders move in each Edit Out mode. You can set the Return Time (time required by Input and Output Channel faders to return to the pre- viously-recorded position) on the Fader1 or 2 page (see page 205). HFADER EDIT This parameter determines how fader moves are rerecorded (it has no effect during the first recording pass). You can select ABSOLUTE or RELATIVE. In Absolute mode, fader moves are rerecorded as absolute values...
Page 203
Automix Main Page203 DM1000 Version 2—Owner’s Manual Automix 16 JOVERWRITE section This section enables you to select parameters to be recorded on the first pass, and rere- corded (i.e., overwritten) on subsequent passes. You can select or deselect these param- eters while recording is in progress (see page 190). KAUTOMIX ENABLED/DISABLED This parameter enables or disables the Automix. When the parameter is set to DISABLE, you cannot record or play back an Automix. If the ESAM function is enabled, you...
Page 204
204Chapter 16—Automix DM1000 Version 2—Owner’s Manual RSTOP Move the cursor to this button, then press [ENTER] to stop Automix recording or play- back. (If you stop recording, a confirmation window appears asking whether you wish to update the Automix data.) The button remains highlighted while Automix is stopped. SABORT This button aborts the current recording without updating the existing Automix data. Automix Memory Page The Automix Memory page enables you to store and recall Automixes. The lower half...
Page 205
Fader1 &2 pages205 DM1000 Version 2—Owner’s Manual Automix 16 IFREE This parameter displays the amount of free memory available for storing the current Automix. JMEMORY This parameter displays the size of the Automix memory selected in the center column. KPROTECT ON/OFF To protect the contents of the Automix memory selected in the MEMORY TITLE col- umn, move the cursor to this button and press [ENTER]. A padlock icon ( ) appears next to the titles of Automix memories that are write-protected. You...
Page 206
206Chapter 16—Automix DM1000 Version 2—Owner’s Manual BMOTOR This button turns the fader motors on or off for Automix playback. The button is high- lighted when the motors are on. CEdit Safe buttons The numbered buttons below each fader bar are Edit Safe buttons, which prohibit Auto- mix recording on certain channels. A channel is set to safe and excluded from Automix recording when its button is highlighted. However, you can play existing events and use faders, Encoders, and [ON] buttons on safe...
Page 207
Editing Events Offline207 DM1000 Version 2—Owner’s Manual Automix 16 Editing Events Offline You can edit recorded Automix events offline on the Event Job and Event Edit pages. You can perform offline editing only while the Automix function is stopped. Event Job Page On the Event Job page, you can erase, copy, move/merge, or trim specified events on spec- ified channels between specified in and out points. 1Press the DISPLAY ACCESS [AUTOMIX] button repeatedly until the Automix | Event Job page appears....
Page 208
208Chapter 16—Automix DM1000 Version 2—Owner’s Manual 4Move the cursor to the desired Job button in the Job Type section, then press [ENTER]. The following Jobs are available. Certain Jobs feature an extra parameter below the TIME SETTING section. ■ERASE This button erases the specified range of Automix data. ■COPY This button copies the specified range of Automix data to another position. When you select this button, the SOURCE and COPY TO sections appear below the TIME SETTING sec- tion. •SOURCE...
Page 209
Editing Events Offline209 DM1000 Version 2—Owner’s Manual Automix 16 ■MOVE/MERGE The function of this button changes depending on the SOURCE section setting. If you select CURRENT (current Automix) in the SOURCE section, this button becomes the MOVE button, which moves the specified range of Automix data to another position. If you select MEM (Automix memories 1–16) in the SOURCE section, this button becomes the MERGE button, which merges the specified range of Automix data with other Automix data. When...
Page 210
210Chapter 16—Automix DM1000 Version 2—Owner’s Manual -Trim amount This parameter specifies the trim amount in the range of –96 dB to +96 dB. 5After setting all necessary parameters, move the cursor to the EXEC button, then press [ENTER]. The PARAMETERS window appears, which enables you to select parameters to be edited, and to perform the selected Job. A parameter is selected when its button is highlighted. (You can specify multiple parame- ters.) These buttons correspond to the following parameters:...