Yamaha Dvx 1000 Owners Manual

Using Libraries181
DM1000 Version 2—Owner’s Manual
Libraries
15
Bus to Stereo Library
You can store Bus to Stereo settings (levels and panpots of signals routed from Bus Outs 1–8 
to the Stereo Bus). The library contains one preset memory and 32 user (readable & writ-
able) memories.
To access the Bus to Stereo library, press the SELECTED CHANNEL [DISPLAY] button 
repeatedly until the Routing | Library page appears.
ACURRENT CONFIGURATION section
Bus Out (1–8) pairing information for the current...

182Chapter 15—Libraries
DM1000 Version 2—Owner’s Manual
ACURRENT TYPE
This parameter displays the currently-selected channel gate type (Gate or Ducking).
BCURRENT CURVE
This graph displays the current channel gate curve.
CGR meters
These meters indicate the amount of gain reduction being applied by the gate, and the 
post-gate levels of the currently-selected channel and its available pair partner.
DType & Curve section
The type (Gate or Ducking) and curve of the currently-selected memory is displayed...

Using Libraries183
DM1000 Version 2—Owner’s Manual
Libraries
15
ACURRENT TYPE
This parameter displays the currently-selected channel comp type (Compressor, 
Expander, Compander Soft, Compander Hard).
BCURRENT CURVE
This graph displays the current compressor curve.
CGR meters
These meters indicate the amount of gain reduction being applied by the compressor, 
and the post-comp levels of the currently-selected channel and its available pair partner.
DType & Curve section
The type and curve of the...

184Chapter 15—Libraries
DM1000 Version 2—Owner’s Manual
EQ Library
This library enables you to store and recall EQ settings for Input Channels, Bus Outs 1–8, 
Aux Outs 1–8, and Stereo Out. The library contains 40 preset memories and 160 user (read-
able & writable) memories.
Follow the steps below to use the EQ library.
1Press the SELECTED CHANNEL EQUALIZER [DISPLAY] button repeatedly to 
display the EQ | EQ Library page.
21Strings3
COMPA variation on preset 20, intended for string instru-
ments with a...

Using Libraries185
DM1000 Version 2—Owner’s Manual
Libraries
15
ACURRENT TYPE
This parameter displays the currently-selected channel EQ type (TYPE I or II).
BCURRENT CURVE
This graph displays the current EQ curve.
CLevel meters
These meters indicate the post-EQ levels of the currently-selected channel and its avail-
able pair partner.
DType & Curve section
The type and curve of the currently-selected EQ program are displayed here.
2Use the LAYER buttons to select layers, then press the [SEL] buttons to...

186Chapter 15—Libraries
DM1000 Version 2—Owner’s Manual
Surround Monitor Library
This library enables you to store and recall Surround Monitor settings. The library contains 
one preset memory that initializes the Surround Monitor settings, and 32 user (readable & 
writable) memories.
To access the Surround Monitor library, press the MONITOR [DISPLAY] button repeat-
edly until the Monitor | Surr Lib page appears. For details on storing and recalling memo-
ries, see “General Library Operation” on page...

Automix187
DM1000 Version 2—Owner’s Manual
Automix
16
16  Automix
This chapter describes the Automix function, which automates real-time mix operation, 
and explains how to use it.
About Automix
The DM1000 features an Automix function, which allows dynamic automation of virtually 
all mix parameters, including Levels, Mutes, Pan, Surround Pan, Aux Sends, Aux Send 
Mutes, EQ, and effects.
Various mixing events can be recorded in Automix. You can also punch channels or param-
eters in and out of recording...

188Chapter 16—Automix
DM1000 Version 2—Owner’s Manual
Setting Up for Automix Recording
This section describes the procedure you must perform before you start Automix recording.
Selecting the Timecode Source
Follow the steps below to select the timecode source and frame rate that the DM1000 uses 
for the Automix function.
1Press the DISPLAY ACCESS [SETUP] button repeatedly until the Setup | Time 
Ref page appears.
This page enables you to select the timecode source for the Automix operation, and the port...

Setting Up for Automix Recording189
DM1000 Version 2—Owner’s Manual
Automix
16
4If you select MIDI CLOCK, press the DISPLAY ACCESS [SETUP] button repeat-
edly until the Setup | MIDI/Host page appears (see page 246). Then, in the 
Rx PORT parameter box, specify the port or slot that receives MIDI Clock.
Creating a Time Signature Map
If you selected the MIDI CLOCK source, you must specify the initial time signature and any 
time signature changes that follow, according to the song. (If you do not do this,...

190Chapter 16—Automix
DM1000 Version 2—Owner’s Manual
Recording an Automix
This section describes a general procedure for Automix recording, including creating a new 
Automix, as well as recording the fader, [ON] button, and other controller events real-time.
Creating a New Automix
Follow the steps below to create a new Automix and select the parameters you want to 
record.
1Connect a timecode source to the DM1000.
2Select the timecode source on the Setup | Time Ref page (see page 188).
If you selected...