Yamaha Dvx 1000 Owners Manual

Using Surround Pan131
DM1000 Version 2—Owner’s Manual
Surround Functions
11
Surround Panning from the Display
You can set the surround pan parameters for each Input Channel from the display.
1Make sure that the DM1000 is in one of the Surround modes, then press the 
[SEL] button of the channel for which you want to set surround pan.
2Press the DISPLAY ACCESS [PAN/SURROUND] button repeatedly until the 
Pan/Surr | Ch Edit page appears.
The Ch Edit page displays the selected Input Channel, and its surround...

132Chapter 11—Surround Functions
DM1000 Version 2—Owner’s Manual
ELFE
This parameter control sets the level of the LFE (Low Frequency Effects) Channel signal 
routed to the subwoofer, and appears only in 5.1 and 6.1 Surround modes.
FDIV
This parameter control determines how the Center signal is fed to the Left, Right, and 
Center channels. It is expressed as a percentage ranging from 0 to 100%. When you set 
the parameter to 100, the Center signal is fed to only the Center channel. When you set 
the...

Using Surround Pan133
DM1000 Version 2—Owner’s Manual
Surround Functions
11
•...................... The sound image moves between front and rear.
•...................... The sound image moves from front right to rear left. With this pattern, 
you can also fine-tune the trajectory by using the WIDTH, DEPTH, 
OFFSET ( ), and OFFSET ( ) parameters.
•...................... The sound image moves from front left to rear right. With this pattern, 
you can also fine-tune the trajectory using the WIDTH, DEPTH,...

134Chapter 11—Surround Functions
DM1000 Version 2—Owner’s Manual
•...................... The sound image moves between front and rear while tracing an arc. 
With this pattern, you can also fine-tune the radius and shape of the 
arc using the WIDTH, DEPTH, OFFSET ( ), and OFFSET ( ) 
parameters.
•...................... The sound image moves while tracing a circle or oval. With this pat-
tern, you can also fine-tune the radius and shape of the circle or oval 
using the WIDTH, DEPTH, OFFSET ( ), and OFFSET (...

Using Surround Pan135
DM1000 Version 2—Owner’s Manual
Surround Functions
11
The following table shows how the sound images on two linked channels move when dif-
ferent trajectory patterns and stereo link patterns are combined. A solid line indicates the 
movement of the selected channel, and a dotted line indicates the movement of the 
linked partner.
8To list multiple-channel surround pan settings, press the [PAN/SURROUND] 
button repeatedly until the Pan/Surr | Surr1–16, Surr17–32, or Surr33–48 
page...

136Chapter 11—Surround Functions
DM1000 Version 2—Owner’s Manual
ASurround pan graphs
These graphs display the trajectory patterns and the current pan positions for the Input 
Channels. Move the cursor to the desired channel’s graph, then rotate the Parameter 
wheel to adjust the pan settings along the selected trajectory pattern. Turning on the 
[GRAB] button enables you to use the Joystick to set the surround pan of the cur-
rently-selected Input Channel.
Press [ENTER] while the cursor is on the graph...

Surround Monitoring137
DM1000 Version 2—Owner’s Manual
Surround Functions
11
The following diagram shows an example of 5.1 Surround Monitor signals patched to 
OMNI OUTs 1–6.
Use the following two buttons in the MONITOR section on the top panel to select the Sur-
round Monitor signal source. If the MIX MONITOR SOURCES check box is checked in the 
Monitor | Surround page, you can select both buttons simultaneously.
•[BUS] button
This button selects the Bus Outs assigned to the surround channels 
as the...

138Chapter 11—Surround Functions
DM1000 Version 2—Owner’s Manual
Configuring Basic Surround Monitoring
You can set basic parameters for Surround Monitor, including  monitor matrix, Bass Man-
agement , and  monitor alignment .
To  do so, press the MONITOR [DISPLAY] button repeatedly until the Monitor | Surr Setup 
page appears.
This page displays the basic parameter settings in the MONITOR FLOW section (
1).
• SURR. MODE
This parameter indicates the current Surround mode. (You cannot change the Surround...

Surround Monitoring139
DM1000 Version 2—Owner’s Manual
Surround Functions
11
The following diagram shows an example in 5.1 Surround mode and 3-1 Monitor Matrix 
mode.
•BASS MANAGEMENT
You can set the filter and attenuator settings for each Surround Monitor Channel using 
eight preset Bass Management modes. The following presets are available:
ATT1: Adjusts the level difference between LR and LsRs.
ATT2: Adjusts the level difference between C and Bs.
AMP: Corrects the LFE channel level.
HPF1–3: Cut the low...

140Chapter 11—Surround Functions
DM1000 Version 2—Owner’s Manual
About the Presets
(1) DVD LFE80Hz
This is a preset optimized for DVD-Video production. The LFE playback bandwidth is set 
up to 80 Hz. When using this preset, we recommend that you use an external device to apply 
an LPF (fc=80 Hz, –24 dB/oct) to the LFE master source.
To monitor audio on DVD-Audio or SACD discs, change the LFE level (AMP) and LPF 
(LPF1) to 0 dB and THRU, respectively, if necessary.
The LFE output gain on some DVD players...