Yamaha Dvx 1000 Owners Manual
Here you can view all the pages of manual Yamaha Dvx 1000 Owners Manual. The Yamaha manuals for Home Theater System are available online for free. You can easily download all the documents as PDF.
Page 91
![Page 91
Naming the Stereo Out and Bus Outs91
DM1000 Version 2—Owner’s Manual
7
Bus Outs
Naming the Stereo Out and Bus Outs
You can change the default Bus names (BUS1, AUX4, STEREO, etc.). It may be convenient
to name the buses “Monitor Out” or “Effect Send,” for example, so that you can easily iden-
tify the signal type.
1Press the DISPLAY ACCESS [OUTPUT PATCH] button repeatedly until the Out
Patch | CH Name page appears.
You can specify Short names in the center column (
1) and Long (full) names in the right...](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-90.png "Page 91
Naming the Stereo Out and Bus Outs91
DM1000 Version 2—Owner’s Manual
7
Bus Outs
Naming the Stereo Out and Bus Outs
You can change the default Bus names (BUS1, AUX4, STEREO, etc.). It may be convenient
to name the buses “Monitor Out” or “Effect Send,” for example, so that you can easily iden-
tify the signal type.
1Press the DISPLAY ACCESS [OUTPUT PATCH] button repeatedly until the Out
Patch | CH Name page appears.
You can specify Short names in the center column (
1) and Long (full) names in the right...")
Naming the Stereo Out and Bus Outs91 DM1000 Version 2—Owner’s Manual 7 Bus Outs Naming the Stereo Out and Bus Outs You can change the default Bus names (BUS1, AUX4, STEREO, etc.). It may be convenient to name the buses “Monitor Out” or “Effect Send,” for example, so that you can easily iden- tify the signal type. 1Press the DISPLAY ACCESS [OUTPUT PATCH] button repeatedly until the Out Patch | CH Name page appears. You can specify Short names in the center column ( 1) and Long (full) names in the right...
Page 92
92Chapter 7—Bus Outs DM1000 Version 2—Owner’s Manual
Page 93
Aux Sends93 DM1000 Version 2—Owner’s Manual 8 Aux Sends 8 Aux Sends This chapter describes how to control Aux Out 1–8. Aux Out 1–8 The Aux Out 1–8 section mixes signals routed from the Input Channels to the correspond- ing Aux Sends, processes them using on-board EQ, compressor, etc., then routes them to the specified internal effects processors, output connectors or I/O card connectors. The DM1000 features eight Aux Sends, which can be used to send signals to the internal and external effects...
Page 94
![Page 94
94Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
Setting Aux Out 1–8 from the Control Surface
You can use the faders, Encoders, [SEL] buttons, and various buttons and controls in the
SELECTED CHANNEL section on the top panel to directly control certain parameters for
Aux Out 1–8.
Setting Levels
To set Aux Out 1–8 levels, press the [MASTER] button in the LAYER section to select the
Master layer, then move faders 1–8. At this time, you can turn Aux Out 1–8 on or off using
the corresponding [ON]...](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-93.png "Page 94
94Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
Setting Aux Out 1–8 from the Control Surface
You can use the faders, Encoders, [SEL] buttons, and various buttons and controls in the
SELECTED CHANNEL section on the top panel to directly control certain parameters for
Aux Out 1–8.
Setting Levels
To set Aux Out 1–8 levels, press the [MASTER] button in the LAYER section to select the
Master layer, then move faders 1–8. At this time, you can turn Aux Out 1–8 on or off using
the corresponding [ON]...")
94Chapter 8—Aux Sends DM1000 Version 2—Owner’s Manual Setting Aux Out 1–8 from the Control Surface You can use the faders, Encoders, [SEL] buttons, and various buttons and controls in the SELECTED CHANNEL section on the top panel to directly control certain parameters for Aux Out 1–8. Setting Levels To set Aux Out 1–8 levels, press the [MASTER] button in the LAYER section to select the Master layer, then move faders 1–8. At this time, you can turn Aux Out 1–8 on or off using the corresponding [ON]...
Page 95
![Page 95
Setting Aux Out 1–8 from the Display95
DM1000 Version 2—Owner’s Manual
8
Aux Sends
Delaying Aux Outs
To delay Aux Out 1–8 signals, press the [ /INSERT/DELAY] button repeatedly until the
/INS/DLY | Out Dly page appears.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels, except that this page does not have the MIX/FB.GAIN parameters (see page 63).
Comp settings
To set the Aux Out 1–8 compressors, press the [DYNAMICS] button, then the [F3] button
to...](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-94.png "Page 95
Setting Aux Out 1–8 from the Display95
DM1000 Version 2—Owner’s Manual
8
Aux Sends
Delaying Aux Outs
To delay Aux Out 1–8 signals, press the [ /INSERT/DELAY] button repeatedly until the
/INS/DLY | Out Dly page appears.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels, except that this page does not have the MIX/FB.GAIN parameters (see page 63).
Comp settings
To set the Aux Out 1–8 compressors, press the [DYNAMICS] button, then the [F3] button
to...")
Setting Aux Out 1–8 from the Display95 DM1000 Version 2—Owner’s Manual 8 Aux Sends Delaying Aux Outs To delay Aux Out 1–8 signals, press the [ /INSERT/DELAY] button repeatedly until the /INS/DLY | Out Dly page appears. The parameters on this page (and the procedure for setting them) are the same as for Input Channels, except that this page does not have the MIX/FB.GAIN parameters (see page 63). Comp settings To set the Aux Out 1–8 compressors, press the [DYNAMICS] button, then the [F3] button to...
Page 96
![Page 96
96Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
EQ settings
To set the EQ for Aux Out 1–8, press the EQUALIZER [DISPLAY] button repeatedly to dis-
play the EQ | EQ Edit page, and use the [SEL] buttons or faders to select Aux Out 1–8.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels (see page 68).
Viewing Aux Out settings
You can view and adjust the parameter settings for the currently-selected Aux Out on the
View | Parameter and Fader pages....](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-95.png "Page 96
96Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
EQ settings
To set the EQ for Aux Out 1–8, press the EQUALIZER [DISPLAY] button repeatedly to dis-
play the EQ | EQ Edit page, and use the [SEL] buttons or faders to select Aux Out 1–8.
The parameters on this page (and the procedure for setting them) are the same as for Input
Channels (see page 68).
Viewing Aux Out settings
You can view and adjust the parameter settings for the currently-selected Aux Out on the
View | Parameter and Fader pages....")
96Chapter 8—Aux Sends DM1000 Version 2—Owner’s Manual EQ settings To set the EQ for Aux Out 1–8, press the EQUALIZER [DISPLAY] button repeatedly to dis- play the EQ | EQ Edit page, and use the [SEL] buttons or faders to select Aux Out 1–8. The parameters on this page (and the procedure for setting them) are the same as for Input Channels (see page 68). Viewing Aux Out settings You can view and adjust the parameter settings for the currently-selected Aux Out on the View | Parameter and Fader pages....
Page 97
![Page 97
Setting Aux Out 1–8 from the Display97
DM1000 Version 2—Owner’s Manual
8
Aux Sends
■Viewing Faders and On/Off Parameters
To display the View | Fader page, use the corresponding [SEL] button or fader to select the
desired Aux Out (1–8), then press the DISPLAY ACCESS [VIEW] button, then the [F2] but-
ton.
•ON/OFF......................... This button turns the currently-selected Aux Out (1–8) on or
off. It links with the corresponding [ON] (1–8) button in the
Master layer....](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-96.png "Page 97
Setting Aux Out 1–8 from the Display97
DM1000 Version 2—Owner’s Manual
8
Aux Sends
■Viewing Faders and On/Off Parameters
To display the View | Fader page, use the corresponding [SEL] button or fader to select the
desired Aux Out (1–8), then press the DISPLAY ACCESS [VIEW] button, then the [F2] but-
ton.
•ON/OFF......................... This button turns the currently-selected Aux Out (1–8) on or
off. It links with the corresponding [ON] (1–8) button in the
Master layer....")
Setting Aux Out 1–8 from the Display97 DM1000 Version 2—Owner’s Manual 8 Aux Sends ■Viewing Faders and On/Off Parameters To display the View | Fader page, use the corresponding [SEL] button or fader to select the desired Aux Out (1–8), then press the DISPLAY ACCESS [VIEW] button, then the [F2] but- ton. •ON/OFF......................... This button turns the currently-selected Aux Out (1–8) on or off. It links with the corresponding [ON] (1–8) button in the Master layer....
Page 98
![Page 98
98Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
Setting Aux Send Levels
You can adjust the level of signals routed from Input Channels to the corresponding Aux
Out (1–8). To do this, you can either use the Encoders on the top panel or set the parameters
on the screen.
Using the Encoders
1Press the AUX SELECT [AUX 1]–[AUX 8] buttons to select the sends.
2Press the ENCODER MODE [AUX] button.
When the ENCODER MODE [AUX] button is turned on, you can rotate the Encoders to
set Aux Send levels....](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-97.png "Page 98
98Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
Setting Aux Send Levels
You can adjust the level of signals routed from Input Channels to the corresponding Aux
Out (1–8). To do this, you can either use the Encoders on the top panel or set the parameters
on the screen.
Using the Encoders
1Press the AUX SELECT [AUX 1]–[AUX 8] buttons to select the sends.
2Press the ENCODER MODE [AUX] button.
When the ENCODER MODE [AUX] button is turned on, you can rotate the Encoders to
set Aux Send levels....")
98Chapter 8—Aux Sends DM1000 Version 2—Owner’s Manual Setting Aux Send Levels You can adjust the level of signals routed from Input Channels to the corresponding Aux Out (1–8). To do this, you can either use the Encoders on the top panel or set the parameters on the screen. Using the Encoders 1Press the AUX SELECT [AUX 1]–[AUX 8] buttons to select the sends. 2Press the ENCODER MODE [AUX] button. When the ENCODER MODE [AUX] button is turned on, you can rotate the Encoders to set Aux Send levels....
Page 99
![Page 99
Setting Aux Send Levels99
DM1000 Version 2—Owner’s Manual
8
Aux Sends
Setting Send Levels from the Display
You can view multiple channels’ Aux Send levels on the screen and adjust them individually.
1Press the AUX SELECT [AUX 1]–[AUX 8] buttons to select the Aux Sends.
2Press the AUX SELECT [DISPLAY] button repeatedly until the page listed
below that contains the desired channels appears.
-Send1-32 page
This page displays the Aux Send levels of Input Channels 1–32.
-Send33-48 page
This page displays the...](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-98.png "Page 99
Setting Aux Send Levels99
DM1000 Version 2—Owner’s Manual
8
Aux Sends
Setting Send Levels from the Display
You can view multiple channels’ Aux Send levels on the screen and adjust them individually.
1Press the AUX SELECT [AUX 1]–[AUX 8] buttons to select the Aux Sends.
2Press the AUX SELECT [DISPLAY] button repeatedly until the page listed
below that contains the desired channels appears.
-Send1-32 page
This page displays the Aux Send levels of Input Channels 1–32.
-Send33-48 page
This page displays the...")
Setting Aux Send Levels99 DM1000 Version 2—Owner’s Manual 8 Aux Sends Setting Send Levels from the Display You can view multiple channels’ Aux Send levels on the screen and adjust them individually. 1Press the AUX SELECT [AUX 1]–[AUX 8] buttons to select the Aux Sends. 2Press the AUX SELECT [DISPLAY] button repeatedly until the page listed below that contains the desired channels appears. -Send1-32 page This page displays the Aux Send levels of Input Channels 1–32. -Send33-48 page This page displays the...
Page 100
100Chapter 8—Aux Sends DM1000 Version 2—Owner’s Manual 3Move the cursor to the FIXED or VARIABLE button in the MODE section for the currently-selected Aux Send to select a mode. •Fixed Mode In this mode, Aux Send levels are fixed at nominal (0.0dB). Also, channel ON/OFF buttons appear instead of the Send level rotary controls and PRE/POST buttons. •Variable Mode In this mode, Aux Send levels are variable and the signal source point can be either pre-fader or post-fader. Channel Send level rotary...