Yamaha Dvx 1000 Owners Manual

Input Channels61
DM1000 Version 2—Owner’s Manual
6
Input Channels
6  Input Channels
This chapter describes how to adjust the DM1000’s Input Channel parameters.
About Input Channels
The input Channel section enables you to adjust the level and tone of the signals input to 
the DM1000 and route the signals to Bus 1–8, Stereo Bus, and Aux Out 1–8. The following 
diagram illustrates the Input Channel signal flow.
• (Phase)
This section switches the phase of input signals.
•GATE
This dynamics processor can be...

62Chapter 6—Input Channels
DM1000 Version 2—Owner’s Manual
•PAN
This section enables you to adjust the pan setting of the signals routed from the Input Chan-
nels to the Stereo Bus. You can also apply the pan setting to a pair of Bus channels.
If the internal Surround Sound setting is activated, the Surround Pan settings for 3-1, 5.1, 
and 6.1 channels are available (see page 125).
•AUX (Aux Send level)
This section enables you to adjust the level of signals routed to Aux Out 1–8. The signals can 
be...

Setting the Input Channels from the Display63
DM1000 Version 2—Owner’s Manual
6
Input Channels
Setting the Input Channels from the Display
To set the Input Channel parameters, you can either move the cursor to the desired param-
eter on the display and change the value, or operate the desired button or control on the top 
panel to directly change the setting.
This section explains how to set the parameters via the display.
Switching the Signal Phase
To switch the phase of each Input Channel, press the [...

64Chapter 6—Input Channels
DM1000 Version 2—Owner’s Manual
The parameters on these three pages (and the procedure for setting them) are the same.
ADELAY SCALE
The following buttons determine the units of the delay value shown below the msec 
value.
•meter............................. Units are set to meters.
•feet................................. Units are set to feet.
•sample........................... Units are set to samples.
•beat................................ Units are set to beats....

Setting the Input Channels from the Display65
DM1000 Version 2—Owner’s Manual
6
Input Channels
Gating Input Channels
To set the Input Channel gates, use the [SEL] buttons to select the desired Input Channel, 
then press the DISPLAY ACCESS [DYNAMICS] button, then the [F1] button. The Dynam-
ics | Gate Edit page appears.
AKEYIN SOURCE
Select one of the following buttons to determine the trigger source for the cur-
rently-selected Input Channel’s gate.
•SELF............................... The selected...

66Chapter 6—Input Channels
DM1000 Version 2—Owner’s Manual
Compressing Input Channels
To set the Input Channel compressors, use the [SEL] buttons to select the desired Input 
Channel, then press the DISPLAY ACCESS [DYNAMICS] button, then the [F3] button to 
display the Dynamics | Comp Edit page.
APOSITION
Use the Parameter wheel, or the [INC]/[DEC] buttons to select the position of the com-
pressor within the channel from the following options:
•PRE EQ.......................... Immediately before EQ...

Setting the Input Channels from the Display67
DM1000 Version 2—Owner’s Manual
6
Input Channels
Attenuating Input Channels
To set the attenuator for each channel, press the SELECTED CHANNEL EQUALIZER 
[DISPLAY] button repeatedly until the page listed below that contains the desired channels 
appears.
-ATT 1-16 page
This page enables you to set the attenuators for Input Channels 1–16.
-ATT 17-32 page
This page enables you to set the attenuators for Input Channels 17–32.
-ATT 33-48 page
This page enables...

68Chapter 6—Input Channels
DM1000 Version 2—Owner’s Manual
EQ’ing Input Channels
The DM1000’s Input Channels feature 4-band (LOW, LOW-MID, HIGH-MID, HIGH) 
parametric EQ. The LOW-MID and HIGH-MID bands are a peaking type of EQ. The LOW 
and HIGH bands can be set to shelving, peaking, or HPF and LPF respectively.
1Press the [SEL] button or move the fader of the channel for which you wish 
to adjust EQ.
2Press the SELECTED CHANNEL EQUALIZER [DISPLAY] button repeatedly to 
display the EQ | EQ Edit page.
The...

Setting the Input Channels from the Display69
DM1000 Version 2—Owner’s Manual
6
Input Channels
FLOW, L-MID, H-MID, HIGH sections
These sections contain the Q, Frequency (F), and Gain (G) parameters for the four 
bands. These parameter values range as follows:
3Move the cursor to the desired parameter, then rotate the Parameter wheel 
to change the value.
Parameter LOW LOW-MID HIGH-MID HIGH
QHPF, 10.0 to 0.10 
(41 steps), L.SHELF10.0 to 0.10 (41 steps)LPF, 10.0 to 0.10 
(41 steps), H.SHELF
Frequency
21.2...

70Chapter 6—Input Channels
DM1000 Version 2—Owner’s Manual
Panning Input Channels
Input Channels can be panned in the range of L63 through CENTER to R63. To pan each 
channel, press the [PAN/SURROUND] button repeatedly until one of the following pages 
that contains the desired channels appears.
-Pan1-32 page
This page enables you to set the pan for Input Channels 1–32.
-Pan33-48 page
This page enables you to set the pan for Input Channels 33–48.
The parameters on these two pages (and the procedure for...