Yamaha Dvx 1000 Owners Manual

Control Surface21
DM1000 Version 2—Owner’s Manual
2
Control Surface & Rear Panel
SELECTED CHANNEL Section
AROUTING [DISPLAY] button
This button displays a Routing page, enabling you to route selected channels to the desired 
Bus, and adjust the level of the signals routed from Buses 1–8 to the Stereo Bus (see page 71 
and 85).
BROUTING [1]–[8] buttons
CROUTING [STEREO] button
DROUTING [DIRECT] button
These buttons select the desired Bus for routing the selected Input Channel signals. The cor-
responding...

22Chapter 2—Control Surface & Rear Panel
DM1000 Version 2—Owner’s Manual
LAYER Section
A[1-16]/[17-32]/[33-48] buttons
These buttons select an Input Channel Layer. The channel strips control Channels 1–16, 
17–32, or 33–48, depending on the button selected here. (See page 33 for more information 
on Layers.)
B[REMOTE 1]/[REMOTE 2] buttons
These buttons select the Remote Layer, which can be used to control external devices, 
including DAWs. (See page 215 for more information on the Remote Layer.)...

Control Surface23
DM1000 Version 2—Owner’s Manual
2
Control Surface & Rear Panel
USER DEFINED KEYS Section
A [DISPLAY] button
This button displays a User Def page, enabling you to assign functions to but-
tons 1–12 (see page 274).
B [1]–[12] buttons
These buttons perform the functions assigned in the User Def pages.
Data Entry Section
A Parameter wheel
This control adjusts the parameter values shown on the display. Turning it 
clockwise increases the value; turning it counterclockwise decreases the...

24Chapter 2—Control Surface & Rear Panel
DM1000 Version 2—Owner’s Manual
MONITOR Section
A[DISPLAY] button
This button displays a Monitor page, enabling you to adjust monitor settings (see page 119 
and 136).
B[SOLO] indicator
This indicator flashes when a single or multiple channels are soloed.
C[CLEAR] button
This button “unsolos” all soloed Channels.
D[2TR D1] button
E[2TR D2] button
F[STEREO] button
These buttons select the Control Room Monitor output signal. When the [2TR D1] button 
indicator is...

Rear Panel25
DM1000 Version 2—Owner’s Manual
2
Control Surface & Rear Panel
Rear Panel
AD Input and Output Section
AINPUT connectors 1–16
These balanced XLR-3-31-type con-
nectors accept line-level and micro-
phone signals. The nominal signal level 
ranges from –60 dB through +4 dB.
BOMNI IN connectors 1–4
These balanced XLR-3-31-type connectors accept line-level signals. The nominal signal 
level is +4 dB.
COMNI OUT connectors 1–4
These balanced XLR-3-32-type con-
nectors output any Bus signals and...

26Chapter 2—Control Surface & Rear Panel
DM1000 Version 2—Owner’s Manual
SLOT Section
ASLOT 1 & 2
You can insert optional mini-YGDAI cards into these slots. (See page 28 for more informa-
tion on installing these cards.)
Digital I/O & Control Section
AMETER connector
This connector enables you to connect an optional MB1000 Meter Bridge.
BCONTROL connector
This 25-pin D-sub connector provides access to the GPI (General Purpose Interface). 
Through this connector, the Talkback function can be turned on and...

Rear Panel27
DM1000 Version 2—Owner’s Manual
2
Control Surface & Rear Panel
GWORD CLOCK OUT connector
This BNC connector outputs a wordclock signal from the DM1000 to a connected external 
device.
HWORD CLOCK IN connector
This BNC connector inputs a wordclock signal from a connected external device to the 
DM1000.
I2TR OUT DIGITAL AES/EBU 1
This XLR-3-31-type connector outputs AES/EBU format digital audio. The connector is 
typically used to connect the digital stereo input (AES/EBU format) of a DAT...

28Chapter 2—Control Surface & Rear Panel
DM1000 Version 2—Owner’s Manual
Installing an Optional Card
Visit the following Yamaha Pro Audio web site to ensure that the card you are installing is 
supported by the DM1000. Also, verify the number of cards (including other Yamaha or 
third-party cards) that can be installed in the unit.
.
Follow the steps below to install an optional mini-YGDAI card.
1Make sure that the power to the DM1000 is turned off.
2Undo the two fixing screws and remove the slot cover,...

Operating Basics29
DM1000 Version 2—Owner’s Manual
3
Operating Basics
3  Operating Basics
This chapter describes basic operations on the DM1000, including how to use the display 
and operate the controls on the top panel.
About the Display
The top panel display indicates various parameters that you must set before you can operate 
the DM1000. The display indicates the following items:
ASelected DISPLAY
This section indicates the currently-selected display page group.
BSelected channel
This section...

30Chapter 3—Operating Basics
DM1000 Version 2—Owner’s Manual
FMIDI indicator
This indicator appears when the DM1000 is receiving MIDI data via the MIDI IN port, 
USB port, REMOTE connector, or an installed MY8-mLAN card.
GSurround mode indicator
This indicator identifies the currently-selected Surround mode (ST=stereo, 3-1, 5.1, or 
6.1) (see page 125).
HSampling rate indicator
This indicator identifies the DM1000’s current sampling rate: 44.1 kHz (44k), 48 kHz 
(48k), 88.2 kHz (88k), or 96 kHz (96k)....