Yamaha Dvx 1000 Owners Manual
Here you can view all the pages of manual Yamaha Dvx 1000 Owners Manual. The Yamaha manuals for Home Theater System are available online for free. You can easily download all the documents as PDF.
Page 101
Setting Aux Send Levels101 DM1000 Version 2—Owner’s Manual 8 Aux Sends 4If you switched to Fixed mode in Step 3, the ON/OFF buttons turn on or off each Input Channel on or off for the currently-selected Aux Send. 5If you switched to Variable mode in Step 3, the PRE/POST buttons and Send level rotary controls enable you to adjust the signal source points and Send levels. You can turn each Input Channel on or off for the currently-selected Aux Send even in Vari- able mode. To do this, move the cursor...
Page 102
![Page 102
102Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
Viewing Aux Send Settings for Multiple Channels
You can view and set parameters for all Aux Send 1–8, including setting levels and Pre/Post
parameters.
This is convenient when you wish to visually check all Aux Send settings or simultaneously
adjust the levels of certain channels routed to Aux 1–8.
1Press the AUX SELECT [DISPLAY] button repeatedly until the page listed
below that contains the desired channels appears.
-View1–16 page
This page...](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-101.png "Page 102
102Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
Viewing Aux Send Settings for Multiple Channels
You can view and set parameters for all Aux Send 1–8, including setting levels and Pre/Post
parameters.
This is convenient when you wish to visually check all Aux Send settings or simultaneously
adjust the levels of certain channels routed to Aux 1–8.
1Press the AUX SELECT [DISPLAY] button repeatedly until the page listed
below that contains the desired channels appears.
-View1–16 page
This page...")
102Chapter 8—Aux Sends DM1000 Version 2—Owner’s Manual Viewing Aux Send Settings for Multiple Channels You can view and set parameters for all Aux Send 1–8, including setting levels and Pre/Post parameters. This is convenient when you wish to visually check all Aux Send settings or simultaneously adjust the levels of certain channels routed to Aux 1–8. 1Press the AUX SELECT [DISPLAY] button repeatedly until the page listed below that contains the desired channels appears. -View1–16 page This page...
Page 103
![Page 103
Viewing Aux Send Settings for Multiple Channels103
DM1000 Version 2—Owner’s Manual
8
Aux Sends
3If you selected the PRE/POST button in Step 2, move the cursor to the desired
Input Channel and Aux intersection, then press the [ENTER] button to
change the signal source point.
4If you selected the LEVEL button in Step 2, move the cursor to the desired
Input Channel and Aux intersection, then edit the Send level or turn the cur-
rently-selected AUX Send on or off.
Rotate the Parameter wheel or press the...](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-102.png "Page 103
Viewing Aux Send Settings for Multiple Channels103
DM1000 Version 2—Owner’s Manual
8
Aux Sends
3If you selected the PRE/POST button in Step 2, move the cursor to the desired
Input Channel and Aux intersection, then press the [ENTER] button to
change the signal source point.
4If you selected the LEVEL button in Step 2, move the cursor to the desired
Input Channel and Aux intersection, then edit the Send level or turn the cur-
rently-selected AUX Send on or off.
Rotate the Parameter wheel or press the...")
Viewing Aux Send Settings for Multiple Channels103 DM1000 Version 2—Owner’s Manual 8 Aux Sends 3If you selected the PRE/POST button in Step 2, move the cursor to the desired Input Channel and Aux intersection, then press the [ENTER] button to change the signal source point. 4If you selected the LEVEL button in Step 2, move the cursor to the desired Input Channel and Aux intersection, then edit the Send level or turn the cur- rently-selected AUX Send on or off. Rotate the Parameter wheel or press the...
Page 104
![Page 104
104Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
Panning Aux Sends
You can pair adjacent odd-even (in this order) Aux Sends for stereo operation. This enables
you to pan signals from Input Channels to paired Aux Sends.
1Pair the desired two Aux Sends. (See page 89 for more information on pair-
ing channels.)
2Use the AUX SELECT [AUX 1]–[AUX 8] buttons to select one of the paired
Aux Sends.
3Press the AUX SELECT [DISPLAY] button repeatedly until the page listed
below that contains the desired...](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-103.png "Page 104
104Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
Panning Aux Sends
You can pair adjacent odd-even (in this order) Aux Sends for stereo operation. This enables
you to pan signals from Input Channels to paired Aux Sends.
1Pair the desired two Aux Sends. (See page 89 for more information on pair-
ing channels.)
2Use the AUX SELECT [AUX 1]–[AUX 8] buttons to select one of the paired
Aux Sends.
3Press the AUX SELECT [DISPLAY] button repeatedly until the page listed
below that contains the desired...")
104Chapter 8—Aux Sends DM1000 Version 2—Owner’s Manual Panning Aux Sends You can pair adjacent odd-even (in this order) Aux Sends for stereo operation. This enables you to pan signals from Input Channels to paired Aux Sends. 1Pair the desired two Aux Sends. (See page 89 for more information on pair- ing channels.) 2Use the AUX SELECT [AUX 1]–[AUX 8] buttons to select one of the paired Aux Sends. 3Press the AUX SELECT [DISPLAY] button repeatedly until the page listed below that contains the desired...
Page 105
![Page 105
Excluding Certain Channels from Aux Sends (Mix Minus)105
DM1000 Version 2—Owner’s Manual
8
Aux Sends
6To link the Input Channel Pan setting with the Aux Send Pan setting, move
the cursor to the INPUT PAN LINK ON/OFF button, then press [ENTER].
The pan positions on the Pan page are copied to the Aux pan setting, and the pan controls
on both pages are linked.
Excluding Certain Channels from Aux Sends (Mix Minus)
You can quickly exclude signals from certain channels from Aux Sends by using the controls...](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-104.png "Page 105
Excluding Certain Channels from Aux Sends (Mix Minus)105
DM1000 Version 2—Owner’s Manual
8
Aux Sends
6To link the Input Channel Pan setting with the Aux Send Pan setting, move
the cursor to the INPUT PAN LINK ON/OFF button, then press [ENTER].
The pan positions on the Pan page are copied to the Aux pan setting, and the pan controls
on both pages are linked.
Excluding Certain Channels from Aux Sends (Mix Minus)
You can quickly exclude signals from certain channels from Aux Sends by using the controls...")
Excluding Certain Channels from Aux Sends (Mix Minus)105 DM1000 Version 2—Owner’s Manual 8 Aux Sends 6To link the Input Channel Pan setting with the Aux Send Pan setting, move the cursor to the INPUT PAN LINK ON/OFF button, then press [ENTER]. The pan positions on the Pan page are copied to the Aux pan setting, and the pan controls on both pages are linked. Excluding Certain Channels from Aux Sends (Mix Minus) You can quickly exclude signals from certain channels from Aux Sends by using the controls...
Page 106
![Page 106
106Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
Copying Channel Fader Positions to Aux Sends
While Aux Sends are in Variable mode, you can copy all Input Channel fader positions on
one layer to the corresponding Aux Sends.
This is convenient when you wish to send to the musicians monitor signals that have the
same balance setting as the Stereo Out signals.
1Press and hold down the copy source layer (LAYER [1-16], [17-32], or [33-48])
button.
2Press one of the AUX SELECT [AUX 1]–[AUX 8] buttons...](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-105.png "Page 106
106Chapter 8—Aux Sends
DM1000 Version 2—Owner’s Manual
Copying Channel Fader Positions to Aux Sends
While Aux Sends are in Variable mode, you can copy all Input Channel fader positions on
one layer to the corresponding Aux Sends.
This is convenient when you wish to send to the musicians monitor signals that have the
same balance setting as the Stereo Out signals.
1Press and hold down the copy source layer (LAYER [1-16], [17-32], or [33-48])
button.
2Press one of the AUX SELECT [AUX 1]–[AUX 8] buttons...")
106Chapter 8—Aux Sends DM1000 Version 2—Owner’s Manual Copying Channel Fader Positions to Aux Sends While Aux Sends are in Variable mode, you can copy all Input Channel fader positions on one layer to the corresponding Aux Sends. This is convenient when you wish to send to the musicians monitor signals that have the same balance setting as the Stereo Out signals. 1Press and hold down the copy source layer (LAYER [1-16], [17-32], or [33-48]) button. 2Press one of the AUX SELECT [AUX 1]–[AUX 8] buttons...
Page 107
![Page 107
Soloing AUX Sends using the [AUX 1]–[AUX 8] Buttons107
DM1000 Version 2—Owner’s Manual
8
Aux Sends
Soloing AUX Sends using the [AUX 1]–[AUX 8] Buttons
You can turn the Solo function on and off using the AUX SELECT [AUX 1]–[AUX 8] but-
tons, without having to switch to the Master layer. This is convenient when you wish to con-
trol the Solo function for Aux Out 1-8 while adjusting the Aux Sends from Input Channels.
1Press the MONITOR [DISPLAY] button repeatedly until the Monitor | Solo
page appears....](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-106.png "Page 107
Soloing AUX Sends using the [AUX 1]–[AUX 8] Buttons107
DM1000 Version 2—Owner’s Manual
8
Aux Sends
Soloing AUX Sends using the [AUX 1]–[AUX 8] Buttons
You can turn the Solo function on and off using the AUX SELECT [AUX 1]–[AUX 8] but-
tons, without having to switch to the Master layer. This is convenient when you wish to con-
trol the Solo function for Aux Out 1-8 while adjusting the Aux Sends from Input Channels.
1Press the MONITOR [DISPLAY] button repeatedly until the Monitor | Solo
page appears....")
Soloing AUX Sends using the [AUX 1]–[AUX 8] Buttons107 DM1000 Version 2—Owner’s Manual 8 Aux Sends Soloing AUX Sends using the [AUX 1]–[AUX 8] Buttons You can turn the Solo function on and off using the AUX SELECT [AUX 1]–[AUX 8] but- tons, without having to switch to the Master layer. This is convenient when you wish to con- trol the Solo function for Aux Out 1-8 while adjusting the Aux Sends from Input Channels. 1Press the MONITOR [DISPLAY] button repeatedly until the Monitor | Solo page appears....
Page 108
108Chapter 8—Aux Sends DM1000 Version 2—Owner’s Manual
Page 109
Input & Output Patching109 DM1000 Version 2—Owner’s Manual 9 Input & Output Patching 9 Input & Output Patching This chapter describes how to patch (assign) signal paths within the DM1000 to its inputs, outputs, and slot channels Input Patching Signals input at INPUT connectors 1–16, 2TR IN DIGITAL connectors 1–2, and Slot I/O cards are patched to Input Channels for use. Patch example: By default, the Input Channels are patched as follows: You can change these patches, if you desire. To change input...
Page 110
![Page 110
110Chapter 9—Input & Output Patching
DM1000 Version 2—Owner’s Manual
Input Patching from the Display
1Press the DISPLAY ACCESS [INPUT PATCH] button repeatedly until the In
Patch | In Patch page appears.
Inputs and slot channels that are currently assigned to Input Channels are shown in the
parameter boxes (
1) below the channel numbers. The parameter indicators are explained
below:
2Move the cursor to an input patch parameter you wish to change, and rotate
the Parameter wheel or press the [INC]/[DEC]...](http://img.usermanuals.tech/thumb/83/53499/w300_yamaha_dvx-1000-owner-s-manual-109.png "Page 110
110Chapter 9—Input & Output Patching
DM1000 Version 2—Owner’s Manual
Input Patching from the Display
1Press the DISPLAY ACCESS [INPUT PATCH] button repeatedly until the In
Patch | In Patch page appears.
Inputs and slot channels that are currently assigned to Input Channels are shown in the
parameter boxes (
1) below the channel numbers. The parameter indicators are explained
below:
2Move the cursor to an input patch parameter you wish to change, and rotate
the Parameter wheel or press the [INC]/[DEC]...")
110Chapter 9—Input & Output Patching DM1000 Version 2—Owner’s Manual Input Patching from the Display 1Press the DISPLAY ACCESS [INPUT PATCH] button repeatedly until the In Patch | In Patch page appears. Inputs and slot channels that are currently assigned to Input Channels are shown in the parameter boxes ( 1) below the channel numbers. The parameter indicators are explained below: 2Move the cursor to an input patch parameter you wish to change, and rotate the Parameter wheel or press the [INC]/[DEC]...