Yamaha Dvx 1000 Owners Manual
Here you can view all the pages of manual Yamaha Dvx 1000 Owners Manual. The Yamaha manuals for Home Theater System are available online for free. You can easily download all the documents as PDF.
Page 121
Using the Solo Function121 DM1000 Version 2—Owner’s Manual Control Room Monitoring 10 DLISTEN This parameter determines the source of the Input Channel Solo signal: Pre Fader or After Pan. When Pre Fader is selected, turning on the PAN button below the Pre Fader option will solo the channel with the pan position specified by the Pan setting even if the source precedes the fader. This parameter is effective only in Recording Solo mode. ESOLO TRIM This parameter enables you to trim the level of the Solo...
Page 122
122Chapter 10—Control Room Monitoring DM1000 Version 2—Owner’s Manual 3To solo and monitor Input Channels, press the corresponding LAYER button to select a Layer that contains the desired channels, then press the channel [SOLO] buttons. The channel [SOLO] button indicators and the MONITOR [SOLO] indicator light up. Only the soloed Input Channel signals are fed to the Control Room Monitor outputs. 4To solo and monitor Output Channels, press the LAYER [MASTER] button, then press the channel [SOLO]...
Page 123
Using the Talkback Function123 DM1000 Version 2—Owner’s Manual Control Room Monitoring 10 BCONTROL ROOM DIMMER LEVEL This parameter determines the amount of attenuation applied to the Control Room Monitor signal by the Dimmer function when you press the MONITOR [DIMMER] button. The amount of attenuation can range from 0 dB to –96 dB. CMONO This button switches the Control Room Monitor signal into mono. DMIX C-R SOURCES Check this check box to select the [2TR D1] or [2TR D2] button and the [STEREO]...
Page 124
124Chapter 10—Control Room Monitoring DM1000 Version 2—Owner’s Manual 1Press the MONITOR [DISPLAY] button repeatedly until the Monitor | C-R/TB page appears. This page contains the following parameters: AOUTPUT ASSIGN section The buttons in this section enable you to assign the Talkback mic signal to the desired outputs. (You can select multiple destinations.) BTALKBACK DIMMER LEVEL When the Talkback function is active, this parameter determines the amount of attenu- ation applied to the Control Room...
Page 125
Surround Functions125 DM1000 Version 2—Owner’s Manual Surround Functions 11 11 Surround Functions This chapter describes surround panning, which determines how Input Channel signals are panned within and across the stereo field. It also describes the DM1000’s surround moni- toring capabilities, which enable you to monitor, in a surround sound environment, DM1000 surround mixes or surround sources input via the slots. Using Surround Pan About Surround Pan The Surround Pan function places a sound image...
Page 126
126Chapter 11—Surround Functions DM1000 Version 2—Owner’s Manual •6.1 This mode uses seven channels that include six channels of 5.1 mode plus rear center. When you select one of these Surround modes, each surround channel is routed to the Buses specified on the Setup | Surr Bus page (see page 130). The following table shows the factory-default Surround Channel to Bus Out assignment in each Surround mode. Surround ModeBUS1 BUS2 BUS3 BUS4 BUS5 BUS6 BUS7 3-1LRCS —— — Front left Front right Center...
Page 127
Using Surround Pan127 DM1000 Version 2—Owner’s Manual Surround Functions 11 You can record each surround channel to a separate track to record surround panning. The following diagram is an example in which each channel signal in 5.1 Surround mode is recorded to digital MTR tracks. Tip: You can set the surround pan either independently of normal panpots or in unison with them. BUS1 (L) BUS2 (R) BUS3 (Ls) BUS4 (Rs) BUS5 (C) BUS6 (LFE)SURROUND PA N LFE LEVEL SURROUND PA N LFE LEVEL SURROUND PA N LFE...
Page 128
128Chapter 11—Surround Functions DM1000 Version 2—Owner’s Manual Setting Up and Selecting Surround Pan Modes To configure the surround environment, select 3-1, 5.1, or 6.1 Surround mode on the DM1000 and connect a multi-channel monitoring system to the DM1000. 1Press the DISPLAY ACCESS [PAN/SURROUND] button repeatedly until the Pan/Surr | Surr Mode page appears. ASURROUND MODE This parameter enables you to select a Surround mode by using the following buttons. The button that is turned on (highlighted)...
Page 129
Using Surround Pan129 DM1000 Version 2—Owner’s Manual Surround Functions 11 3Press the [ENTER] button. The confirmation window for changing the Surround mode appears. 4Move the cursor to the YES button, then press [ENTER]. The DM1000 enters the selected Surround mode. 5To link the Input Channel Pan setting with the stereo surround panning, move the cursor to the PAN/SURR LINK button, then press [ENTER]. When the PAN/SURR LINK button is turned on, adjusting the Input Channel pan settings will also change...
Page 130
130Chapter 11—Surround Functions DM1000 Version 2—Owner’s Manual 6To change the Surround Channel to Bus Out assignment, move the cursor to the SURR/BUS SETUP button, then press [ENTER]. The Setup | Surr Bus page appears. ABUS1–BUS8 These parameters select channels to be assigned to the Bus Outs in 3-1, 5.1, and 6.1 Sur- round modes. BINIT These buttons reset the channel assignment to the default setting. 7To change the assignment, move the cursor to the desired Bus parameter, rotate the Parameter wheel...