Yamaha Dvx 1000 Owners Manual

Bus Outs81
DM1000 Version 2—Owner’s Manual
7
Bus Outs
7  Bus Outs
This chapter describes how to adjust the DM1000’s Stereo Out and Bus Out parameters.
About Stereo Out
The Stereo Out section receives Input Channel and Bus Out 1–8 signals, mixes them into 
two channels, processes them using on-board EQ, compressor, etc., then routes them to two 
channel output connectors. The following diagram illustrates the Stereo Out signal flow.
•INSERT
This section enables you to route the Stereo Out signals to...

82Chapter 7—Bus Outs
DM1000 Version 2—Owner’s Manual
Bus Out 1–8
The Bus Out 1–8 section mixes signals routed from Input Channels to the specified buses, 
processes them using on-board EQ, compressor, etc., then routes them to the specified out-
put connectors or I/O cards.
The following diagram illustrates the Bus Out signal flow.
•INSERT
•ATT (Attenuator)
•4 BAND EQ (4-band equalizer)
•COMP (Compressor)
•ON (On/Off)
•LEVEL
•OUTPUT DELAY (Output delay)
•METER
The parameters and sections listed above are...

Setting the Stereo Out and Bus Out 1–8 from the Display83
DM1000 Version 2—Owner’s Manual
7
Bus Outs
Setting the Stereo Out and Bus Out 1–8 from the Display
To set the Stereo Out and Bus Out 1–8 parameters, you can either move the cursor to the 
desired parameter on the display and change the value, or operate the desired button or 
control on the top panel.
This section explains how to set the parameters on the display.
Attenuating the Stereo Out and Bus Out
To attenuate the Stereo Out and Bus Out...

84Chapter 7—Bus Outs
DM1000 Version 2—Owner’s Manual
Compressing the Stereo Out and Bus Outs
To set the Stereo Out and Bus Out 1–8 compressors, press the [DYNAMICS] button, then 
the [F3] button to display the Dynamics | Comp Edit page, and use the [SEL] buttons or 
faders to select the Stereo Out or Bus Out 1–8.
The parameters on this page (and the procedure for setting them) are the same as for Input 
Channels (see page 66).
EQ’ing the Stereo Out and Bus Outs
To set the EQ for the Stereo Out and Bus...

Setting the Stereo Out and Bus Out 1–8 from the Display85
DM1000 Version 2—Owner’s Manual
7
Bus Outs
Routing Bus Out 1–8 Signals to the Stereo Bus
You can patch Bus Out 1–8 signals to Outputs and Slots 1/2, as well as to the Stereo Bus. You 
can adjust the level and pan settings of the signals routed to the Stereo Bus for each bus. This 
is convenient when you wish to use Bus Outs (1–8) as a Group Bus.
To patch the Bus Out 1–8 signals to the Stereo Bus, press the SELECTED CHANNEL 
ROUTING [DISPLAY]...

86Chapter 7—Bus Outs
DM1000 Version 2—Owner’s Manual
Viewing the Stereo Out and Bus Out Settings
You can view and adjust parameter settings for the currently-selected Stereo Out or Bus Out 
on the View | Parameter and Fader pages.
■Viewing the Compressor and EQ Settings
To display the View | Parameter page, use the corresponding [SEL] button or fader to select 
the desired bus, then press the DISPLAY ACCESS [VIEW] button, then the [F1] button.
The parameters on this page (and the procedure for setting...

Setting the Stereo Out and Bus Out 1–8 from the Display87
DM1000 Version 2—Owner’s Manual
7
Bus Outs
CFader
This fader adjusts the Stereo Out output levels, and links with the [STEREO] fader. The 
fader knob is highlighted when the fader is set to 0.0 dB.
•Bus Out (1–8) Fader page
AON/OFF
This button turns the currently-selected Bus Out (1–8) on or off, and links with the 
[ON] (9–16) button in the Master layer.
BFader
This fader sets the currently-selected Bus Out (1–8) level, and links with the fader...

88Chapter 7—Bus Outs
DM1000 Version 2—Owner’s Manual
Setting the Stereo Out and Bus Out 1–8 from the 
Control Surface
You can use the faders, Encoders, [SEL] buttons, and various buttons and controls in the 
SELECTED CHANNEL section on the top panel to directly control certain parameters for 
the Stereo Out and Bus Out 1–8.
Setting the Levels
Move the [STEREO] fader to adjust the Stereo Out levels. Press the [ON] button in the STE-
REO section to turn the Stereo Out on or off.
To set Bus Out 1–8 levels,...

Pairing Buses or Aux Sends89
DM1000 Version 2—Owner’s Manual
7
Bus Outs
Pairing Buses or Aux Sends
You can pair adjacent odd-even (in this order) buses or Aux Sends for stereo operation. 
Paired bus and Aux Send linked parameters and non-linked parameters (that are available 
for independent controls) are listed below:
** You can set this parameter for each channel independent-
ly if the GANG button is turned off on the  /INS/DLY | 
DLY page.
*** You can set this parameter for each channel independent-...

90Chapter 7—Bus Outs
DM1000 Version 2—Owner’s Manual
Attenuating Output Signals
To attenuate the DM1000’s output signals, display the EQ | Out Att page and adjust the Ste-
reo Out and Bus Out 1–8 attenuators individually.
If necessary, you can also select Output and I/O card channels and specify the amount of 
attenuation. This technique is convenient when you want to attenuate output signals 
quickly, regardless of the source signal patching.
1Press the DISPLAY ACCESS [SETUP] button repeatedly until the...