Yamaha Dvx 1000 Owners Manual
Here you can view all the pages of manual Yamaha Dvx 1000 Owners Manual. The Yamaha manuals for Home Theater System are available online for free. You can easily download all the documents as PDF.
Page 241
MIDI Remote Layer241 DM1000 Version 2—Owner’s Manual Remote Control 17 9Move the cursor to the LATCH/UNLATCH button, then press [ENTER] to select LATCH or UNLATCH depending on how you want the [ON] buttons to function. •LATCH........................... Pressing the [ON] buttons repeatedly transmits alternating On and Off messages. •UNLATCH.................... Pressing and holding down the [ON] buttons transmits On messages, and releasing the [ON] buttons transmits Off mes- sages. ■When “SW” is...
Page 242
242Chapter 17—Remote Control DM1000 Version 2—Owner’s Manual Machine Control Function The DM1000 can control the transport functions and select tracks on external recording machines that support MMC and the P2 protocol by transmitting commands via the MIDI OUT port and REMOTE connector respectively. 1Refer to the diagram below for information on connecting the DM1000 to an external device. 2To control a device that supports the P2 protocol, press the DISPLAY ACCESS [SETUP] button repeatedly to...
Page 243
Machine Control Function243 DM1000 Version 2—Owner’s Manual Remote Control 17 3Press the DISPLAY ACCESS [SETUP] button repeatedly until the Setup | MIDI/Host page appears. 4 Move the cursor to either the MMC button or P2 button in the MACHINE CONTROL section ( 1) to specify the remote control method, then press the [ENTER] button. In the MACHINE CONTROL section, you can also select the type of commands used on the Remote | Machine Control page. The MMC button selects MMC commands, and the P2 button...
Page 244
244Chapter 17—Remote Control DM1000 Version 2—Owner’s Manual 7To start remote control, press the DISPLAY ACCESS [REMOTE] button, then press the [F3] button to display the Remote | Machine page. This page contains the following parameters: ALOCATE/TIME section This section enables you to set the locate points. •LOCATE 1–8................. These buttons locate the positions (specified by the TIME val- ues) on external machines. •RTZ................................ This Return To Zero button locates the...
Page 245
MIDI245 DM1000 Version 2—Owner’s Manual MIDI 18 18 MIDI This chapter describes the DM1000’s MIDI-related functions. MIDI & the DM1000 Using Control Changes, Program Changes, and other MIDI messages enables you to recall Scenes and edit parameters on the DM1000, and store DM1000 internal data on external MIDI devices. The DM1000 supports the following MIDI messages. Each of these MIDI messages can be individually turned on or off for transmission and reception. •Program Changes If you assign the...
Page 246
246Chapter 18—MIDI DM1000 Version 2—Owner’s Manual •USB port This port is used to connect a computer and transfer MIDI messages. This is a multiport interface that transmits and receives up to eight-port data (16 channels x 8 ports). If you connect a computer to the USB port, you must install the appropriate driver software on the computer. See the Studio Manager Installatio n Guide for more information on install- ing drivers. • REMOTE connector This connector normally enables you to remotely control...
Page 247
MIDI Port Setup247 DM1000 Version 2—Owner’s Manual MIDI 18 •Rx PORT....................... This parameter specifies a port for general MIDI data recep- tion. In the left parameter box, select MIDI, USB, SLOT1, or REMOTE. If you select USB, specify the port number in the right parameter box. •Tx PORT........................ This parameter specifies a port for general MIDI data transmis- sion. The available ports are the same as for the Rx PORT parameter. BMIDI THRU section These parameters enable you to...
Page 248
248Chapter 18—MIDI DM1000 Version 2—Owner’s Manual Selecting MIDI Messages for Transmission and Reception You can select MIDI messages to be transmitted or received at a port specified in the GEN- ERAL section on the Setup | MIDI/Host page (see page 246). To do so, press the DISPLAY ACCESS [MIDI] button repeatedly until the MIDI | Setup page appears. Select MIDI channels for transmission and reception in the CHANNEL row, and turn the transmission and reception of each MIDI message on or off using the...
Page 249
Assigning Scenes to Program Changes for Remote Recall249 DM1000 Version 2—Owner’s Manual MIDI 18 •Tx ON/OFF................... Transmission of Parameter Change messages is enabled or dis- abled. •Rx ON/OFF ................... Reception of Parameter Change messages is enabled or disabled. •ECHO ON/OFF............ This button determines whether Parameter Change messages received at the MIDI IN port are echoed through to the MIDI OUT port. EBULK This parameter row enables or disables reception of Bulk...
Page 250
250Chapter 18—MIDI DM1000 Version 2—Owner’s Manual 4Move the cursor to a parameter box in the PGM CHG column, and rotate the Parameter wheel or press the [INC]/[DEC] buttons to select the Program Change numbers to which you want to assign Scenes. 5Press the cursor button [ ] to move the cursor to a parameter box in the SCENE NO./TITLE column, then rotate the Parameter wheel or press the [INC]/[DEC] buttons to select Scenes. 6Press the DISPLAY ACCESS [MIDI] button repeatedly until the MIDI | Setup...