Yamaha Dvx 1000 Owners Manual

Crossfade via ESAM Commands261
DM1000 Version 2—Owner’s Manual
Controlling the DM1000 
from a Video Editor
19
4Press the DISPLAY ACCESS [SETUP] button repeatedly until the Setup | Time 
Ref page appears.
5Move the cursor to the FRAMES parameter, then select the desired frame 
rate.
The Transition Time transmitted from a video editor is expressed in frames. Match the 
frame rate.
6Press the DISPLAY ACCESS [REMOTE] button repeatedly until the Remote | 
ESAM 1-32 page or ESAM 33-48 page appears.
7Assign...

262Chapter 19—Controlling the DM1000 from a Video Editor
DM1000 Version 2—Owner’s Manual
9Move the cursor to the MOTOR button, then press [ENTER] to turn the motor 
faders on or off.
When the MOTOR button is turned off, the motor faders will not move even when the 
DM1000 receives the ESAM commands. (However, the fader levels will change.)
10 Set each channel routing on the Routing page (page 71).
Use BUS 1–8 as sends to the REC machine. The routing settings will differ as follows 
depending on whether...

Crossfade via ESAM Commands263
DM1000 Version 2—Owner’s Manual
Controlling the DM1000 
from a Video Editor
19
13 Set the pre-crossfade FROM machine level (the fader’s initial value) and the 
post-crossfade TO machine level (the fader’s target value).
Set the stereo fader to 0 dB. If you’re not using pre-read, you’ll need to set the channel fader 
of the REC machine to 0 dB in order to monitor the return from the REC machine.
-Setting the FROM machine level
Use the fader to adjust the level of the FROM...

264Chapter 19—Controlling the DM1000 from a Video Editor
DM1000 Version 2—Owner’s Manual
Video Editors with confirmed compatibility
As  of June 2004, we have confirmed that this system operates correctly with the following 
video e ditors.
•S ony BVE2000, 9100
•A ccom Axial 2010, 2020, 3000
•A mpex ACE200
•P anasonic AG A850
Fo r the most recent information, check the following website.
http://www.yamahaproaudio.com/
Supported Commands
All commands are Write commands that will be used to change the status...

Other Functions265
DM1000 Version 2—Owner’s Manual
Other Functions
20
20  Other Functions
This chapter describes the DM1000’s miscellaneous functions.
Changing the Input and Output Connector Names
You can change the default name of the input and output connectors, if you desire.
Changing the Input Connector Names
1Press the DISPLAY ACCESS [SETUP] button repeatedly until the Setup | In 
Port page appears.
You can specify Short names in the parameter boxes (
1) in the center column, and Long 
names in the...

266Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
Changing the Output Connector Names
To change output connector names, press the DISPLAY ACCESS [SETUP] button repeat-
edly until the Setup | Out Port page appears.
The procedure for editing the names and using the Name Output Auto Copy check box and 
the INITIALIZE button is the same as on the In Port page.
Setting Preferences
You can change the default settings and environmental settings of the DM1000 by using the 
Setup | Prefer1, Prefer2,...

Setting Preferences267
DM1000 Version 2—Owner’s Manual
Other Functions
20
•Auto PAN/SURROUND Display
If this check box is on, the Pan/Surr pages appear automatically when you operate the Joy-
stick in the SELECTED CHANNEL section. If you want to use the Joystick to adjust the pan 
setting, turn on this check box. In Stereo Surround mode, operating the Joystick enables 
you to adjust the Pan setting. Otherwise, it enables you to adjust the Surround Pan settings.
•Auto EQUALIZER Display
If this check box...

268Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
•Initial Data Nominal
If this check box is on, Input Channel faders are set to nominal (0  dB) when you recall Scene 
#0.
•Meter Follow Layer
If this check box is on, a connected optional MB1000 Meter Bridge automatically track a 
layer selection made in the LAYER section on the DM1000.
•Scene MEM Auto Update
If this check box is on, you can use the Scene Memory Auto Update function (see page 167).
•Joystick Auto Grab
If this check box is on,...

Setting Preferences269
DM1000 Version 2—Owner’s Manual
Other Functions
20
BPort ID/PORT
This parameter selects a format for the port name displayed on the pages. When the Port 
ID check box is on, the Port ID (such as AD1 or OMN10) appears. When the Port Short 
Name check box is on, the Short Port name appears (see page 266).
CChannel Copy Parameter
This parameter selects the channel parameters to be copied when you assign the Chan-
nel Copy function to one of the User Defined buttons (see page 274). You...

270Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
Prefer3 page
This page enables you to set various Automix preferences.
This page contains the following parameters. (These parameters are explained in the order 
from the top of the left column to the bottom of the right column).
•Mix Update Confirmation
If this check box is on, when Automix recording stops, a confirmation message appears  ask-
ing if you want to update the current Automix with the latest edits.
•Auto EQ Edit in
If this check...