Yamaha Dvx 1000 Owners Manual

Using Operation Lock281
DM1000 Version 2—Owner’s Manual
Other Functions
20
CPASSWORD
This button enables you to change the current password. Move the cursor to the PASS-
WORD button, then press [ENTER]. The Set Password window appears, enabling you 
to change the password.
Enter the current password in the PASSWORD field, and a new password in the NEW 
PASSWORD field. The factory default password is “1234.” Enter the new password again 
in the REENTRY field located below the NEW PASSWORD field. Move the...

282Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
Cascading Consoles
The DM1000 features a Cascade Bus that enables cascade connection. You can connect two 
DM1000s in cascade using the digital inputs and outputs, or the OMNI IN and OMNI 
OUT connectors. In this way, two consoles work just like one big console, integrating each 
unit’s Buses 1–8, Aux Sends 1–8, Stereo Bus, and Solo Bus.
The following DM1000 functions are linked via the cascade connection. To link functions 
and parameters...

Cascading Consoles283
DM1000 Version 2—Owner’s Manual
Other Functions
20
The following paragraphs explain how to make a cascade connection using two DM1000s 
and the inputs and outputs of digital I/O cards installed in the slots of two DM1000s.
1Install digital I/O cards into Slot 1 or 2 on two DM1000s.
2Connect two DM1000s as follows:
•If you want to use the REMOTE connector to transfer MIDI messages, connect the 
REMOTE connector of each DM1000 using a 9-pin D-sub reverse cable. If you want to 
use the...

284Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
4Assign the Bus signals to the slot channels that are used for the cascade con-
nection.
The following signals are available:
The following display page is an example of integrating Bus 1–8, Aux Send 1–4, Stereo Bus, 
and Solo Bus signals via two 8-channel digital I/O cards (such as MY8-AT).
5On the master unit, press the DISPLAY ACCESS [INPUT PATCH] button 
repeatedly until the In Patch | Cascade In page appears.
6Select the Input Channels on...

Cascading Consoles285
DM1000 Version 2—Owner’s Manual
Other Functions
20
7On the master unit, press the DISPLAY ACCESS [DIO] button repeatedly until 
the DIO | Cascade page appears, then adjust the Attenuators using the 
parameter controls.
The DIO | Cascade page enables you to adjust the level of signals input to the Cascade Bus 
using the dedicated attenuators. You can also turn the Cascade Buses on or off using the but-
tons below the parameter controls.
8On the slave unit, press the DISPLAY ACCESS...

286Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
10 Repeat Steps 8 and 9 for the master unit so that it will be able to transmit 
and receive MIDI messages via the REMOTE connector.
11 To match the parameters of both DM1000s, locate the Setup | MIDI/Host 
page on the copy source unit.
12 Move the cursor to the TRANSMIT button for the SYNC parameter, then 
press [ENTER].
Parameters for cascade link (page 282) will be copied to the other DM1000 via the 
REMOTE connector. If you select the...

Using the AD8HR/AD824287
DM1000 Version 2—Owner’s Manual
Other Functions
20
Using the AD8HR/AD824
The Yamaha AD8HR/AD824, an 8-channel AD converter, enables you to control its gain 
and phantom power from a connected DM1000. The DM1000 can control up to four 
AD8HR/AD824s simultaneously.
If you connect the DM1000 to the AD8HR/AD824 digitally, and connect the DM1000 
REMOTE connector to the AD8HR/AD824 REMOTE connector using a serial cable, you 
can use the AD8HR/AD824 as AD Inputs for which you can...

288Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
3Press the DISPLAY ACCESS [SETUP] button repeatedly until the Setup | 
Remote page appears.
This page contains the following parameters:
AREMOTE FUNCTION
This parameter selects a device to be connected to the DM1000 REMOTE connector.
BHA section
This section enables you to specify the slot channels that will receive eight channel sig-
nals from AD8HR/AD824s that have their ID numbers set to 1 through 4.
CHA CONTROL section
This section enables...

Checking the Battery and the System Version289
DM1000 Version 2—Owner’s Manual
Other Functions
20
Checking the Battery and the System Version
The Utility | Battery page enables you to check the condition of the internal mem-
ory-backup battery and the system version number. To locate this page, press the DISPLAY 
ACCESS [UTILITY] button repeatedly.
AStatus
If  the Status is “Okay,” the battery has sufficient voltage for operation. If the Status is 
“V oltage low!,” ask your Yamaha dealer to replace the...

290Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
3To reset the DM1000 to factory default settings, move the cursor to the INI-
TIALIZE button, then press [ENTER].
To cancel the initialization operation, move the cursor to the CANCEL button, then press 
[ENTER].
When the internal data is thoroughly overwritten, the DM1000 restarts using the factory 
settings.
4To reset the Operation Lock password to its initial setting, in Step 2, move 
the cursor to the PASSWORD button, then press [ENTER]....