Yamaha Dvx 1000 Owners Manual

Setting Preferences271
DM1000 Version 2—Owner’s Manual
Other Functions
20
•Automix Store Undo
If this check box is on, you can undo the Automix Store & Clear functions.
•Touch Sence Edit In ALL
If this check box is on, all parameters that are turned on in the OVERWRITE section on the 
Automix | Main page will be punched in and out via the faders’ Touch Sense function. If this 
check box is off, only the faders selected in Fader mode will be punched in and out.
•Drop Out Time
This parameter sets an...

272Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
Creating a Custom Layer by Combining Channels (User 
Assignable Layer)
If you set the Remote Layer target to “USER ASSIGNABLE,” you can create a custom layer 
by combining any DM1000 channels (excluding the Stereo Out). This custom layer is called 
“User Assignable layer.” You can use either Remote 1 or Remote 2 for a User Assignable layer.
1Press the DISPLAY ACCESS [REMOTE] button, then press the [F1] or [F2] but-
ton.
The Remote | Remote1 or...

Using the Oscillator273
DM1000 Version 2—Owner’s Manual
Other Functions
20
Using the Oscillator
The DM1000 features an Oscillator you can use for sound checks. Follow the steps below to 
use the Oscillator:
1Press the DISPLAY ACCESS [UTILITY] button, then press the [F1] button.
The Utility | Oscillator page appears.
This page contains the following parameters:
AOSCILLATOR ON
This parameter button turns the Oscillator on or off.
BWAVEFORM
These parameter buttons select the Oscillator waveforms.
CLEVEL...

274Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
5Move the cursor to the OSCILLATOR ON/OFF button, then press the [ENTER] 
or [INC]/[DEC] buttons to turn on the Oscillator.
The Oscillator signal is now routed to the channels selected in the ASSIGN section.
6Move the cursor to the parameter control in the LEVEL section, then rotate 
the Parameter wheel to raise the Oscillator level.
You can view the current Oscillator level on the LEVEL meter.
Using the User Defined Keys
You can assign any of...

Using the User Defined Keys275
DM1000 Version 2—Owner’s Manual
Other Functions
20
2Move the cursor to the desired BANK parameter button, then press [ENTER].
The corresponding bank is selected, and the functions assigned to the User Defined buttons 
in that bank are displayed in the 1–12 parameter boxes.
3Move the cursor to one of the 1–12 parameter boxes, then press [ENTER].
The DM1000 displays the User Define Select window, which enables you to assign functions 
to the selected buttons.
4Move the cursor...

276Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
Using GPI (General Purpose Interface)
The DM1000’s CONTROL port  provides a GPI (General Purpose Interface) for controlling 
external equipment. You can configure the GPI so that it will output 8-channel trigger sig-
nals when you operate the faders or USER DEFINED KEYS, or so that it will receive 4-chan-
nel trigger signals to control the DM1000 parameters.
You can assign functions to these trigger signals. In this way, for example, you can...

Using GPI (General Purpose Interface)277
DM1000 Version 2—Owner’s Manual
Other Functions
20
2To assign functions to the incoming trigger signals, move the cursor to one 
of four trigger signal parameters 1–4 in the INPUT section.
3Rotate the Parameter wheel to select the desired function from the list below 
the INPUT section, then press [ENTER] to confirm the selection.
4Select one of two buttons located to the right of trigger signal parameters 
1–4 to specify how the incoming trigger signals will be...

278Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
At this time, the trigger signal is output from the CONTROL port when you operate the 
assigned parameters or controls.
■Parameters available in the INPUT section
•TALKBACK/DIMMER.......................Same as the MONITOR [TALKBACK] and 
[DIMMER] button functions.
•BUS/SLOT............................................Same as the MONITOR [BUS] and [SLOT] but-
ton functions.
•STEREO/2TRD1/2TRD2....................Same as the MONITOR [STEREO],...

Using GPI (General Purpose Interface)279
DM1000 Version 2—Owner’s Manual
Other Functions
20
•xxx UNLATCH............. The assigned button function is enabled only while the incom-
ing trigger signal is active.
•xxx ON........................... The corresponding channels are turned on or off each time the 
incoming trigger signal becomes active.
•xxx ON UNLATCH...... The corresponding channels are turned on only while the 
incoming trigger signal is active.
•UDEFxxx....................... Same as the...

280Chapter 20—Other Functions
DM1000 Version 2—Owner’s Manual
Using Operation Lock
The DM1000 features an Operation Lock function that prevents unintentional edits and 
restricts access to panel operation with a password.
To use the Operation Lock function, press the [UTILITY] button, then the [F4] button to 
display the Utility | Lock page.
This page contains the following parameters:
AOPERATION LOCK
This button enables or cancels Operation Lock. When you turn on this button, the Pass-
word window...