Xerox 1632 2240 3535 Color Carrera Manual

6/02
2-211 DC1632/2240
12-254
Status Indicator RAPs Prelaunch Training/Review
12-254 Stacker Trayï The Stack Height Sensor did not detect that the tray went down within 500ms after the
Stacker Tray lowered at initialization.
ï The Stack Height Sensor did not detect that the tray went up within 5sec after the Stacker
Tray  lifted up.ProcedureCheck the Stack Height Sensor Actuator for disengagement, bending, and breakage.
Enter dC330 [012-201] and press Start.  Manually turn the Stack Height Sensor...

6/02
2-212DC1632/2240
12-254
Prelaunch Training/Review Status Indicator RAPsFigure 4 Finisher PWB 

6/02
2-213 DC1632/2240
12-255
Status Indicator RAPs Prelaunch Training/Review
12-255 Stacker Tray Upper Limitï The system detected that the Stacker Tray Upper Limit Sensor was turned on after the
Stacker Tray had begun lifting up.
ï The system detected that the Stacker Tray Upper Limit Sensor remained on when lower-
ing down of the Stacker Tray has completed.ProcedureEnter dC330 [012-202] and press Start.  Actuate the Upper Limit Sensor. The display
changes.
YN
Check the Upper Limit Sensor using the...

6/02
2-214DC1632/2240
12-255
Prelaunch Training/Review Status Indicator RAPsFigure 3 Stack Height Sensor
Figure 4 Stacker Motor CD
Figure 5 Finisher PWB 

6/02
2-215 DC1632/2240
12-256
Status Indicator RAPs Prelaunch Training/Review
12-256 Staple Front Corner Sensor Onï The Stapler Front Corner Sensor does not turn on within 2sec after starting to move to
Front Corner.
ï The Stapler Front Corner Sensor remained on when starting to move to Front Corner.ProcedureOpen the Finisher Front Cover.  Turn the Stapler Assembly manually. The Staple Head
moves smoothly without any load.
YN
Repair the cause of Staple Head not moving, such as rail breakage, drag, or...

6/02
2-216DC1632/2240
12-256
Prelaunch Training/Review Status Indicator RAPsFigure 4 Finisher PWB 

6/02
2-217 DC1632/2240
12-257
Status Indicator RAPs Prelaunch Training/Review
12-257 Staple Front Corner Sensor Offï The Staple Front Corner Sensor does not turn off after the move from Front Corner has
completed.
ï The Staple Front Corner Sensor does not turn off within 200ms after starting to move from
Front Corner.ProcedureOpen the Finisher Front Cover.  Turn the Stapler Assembly manually. The Staple Head
moves smoothly without any load.
YN
Remove the cause of Staple Head not moving, such as rail...

6/02
2-218DC1632/2240
12-257
Prelaunch Training/Review Status Indicator RAPsFigure 4 Finisher PWB 

6/02
2-219 DC1632/2240
12-260
Status Indicator RAPs Prelaunch Training/Review
12-260 Eject Clamp Home Sensor OnThe Eject Clamp Home Sensor does not turn on after the Eject Clamp up started.ProcedureRemove the Eject Clamp Home Sensor bracket. (Leave the Connector plugged in)
Enter dC330 [012-210] and press Start.  Actuate the Eject Clamp Home Sensor with a sheet of
paper. The display changes.
YN
Check the Eject Clamp Home Sensor using the Generic Transmissive Sensor RAP.
Restore the Sensor to the original...

6/02
2-220DC1632/2240
12-260
Prelaunch Training/Review Status Indicator RAPsFigure 4 Finisher PWB