Xerox 1632 2240 3535 Color Carrera Manual

6/02
2-201 DC1632/2240
12-122
Status Indicator RAPs Prelaunch Training/Review
12-122 Compiler Entrance Sensor OffPaper does not deactuate the Compiler Entrance Sensor.ProcedureMake a copy and observe paper in the Compiler Tray. The copy enters the Compiler Tray.
YN
There is a drives problem.  Check the following:
ï The paper path failure for burr and foreign substance.
ï The Drive Transmission Gear from the Finisher Drive Motor for wear and breakage
ï The Decurler Roll/pinch Roll for a drive failure
ï...

6/02
2-202DC1632/2240
12-170
Prelaunch Training/Review Status Indicator RAPs
12-170 Set EjectThe Compiler Paper Sensor did not deactuate after the Eject Motor energized.ProcedureEnter dC330 [012-102] and press Start.  Actuate and deactuate the Compiler Paper Sensor.
The display changes.
YN
Repair the sensor as required (PL 17.10) for mechanical problems.  If the sensor is
mechanically good, check the circuit of the Compiler Paper Sensor (Figure 2). 
Check the following:
ï Eject Roll for contamination,...

6/02
2-203 DC1632/2240
12-241
Status Indicator RAPs Prelaunch Training/Review
12-241 Staple Move Sensor Onï The Staple Move Sensor did not turn on within 2sec after the system has started to move
to the Staple Position and the Staple Move Sensor has turned off.
ï The Staple Move Sensor did not turn on after the move to the Staple Position has com-
pleted.ProcedureThe Staple Head move smoothly without any load.
YN
Remove the cause of Staple Head not moving, such as rail breakage, drag, and gnawed
gear....

6/02
2-204DC1632/2240
12-242
Prelaunch Training/Review Status Indicator RAPs
12-242 Staple Move Sensor Offï The Staple Move Sensor did not turn off within 500ms after the move to the Staple Posi-
tion has started. 
ï The Staple Move Sensor turned off after Staple Position has been fixed.
ï The Staple Move Sensor did not turn off within 500ms after it has turned on when paper
passed through the 1st position of the DUAL STAPLE at moving to the Rear Staple Posi-
tion.ProcedureOpen the Finisher Front Cover....

6/02
2-205 DC1632/2240
12-244
Status Indicator RAPs Prelaunch Training/Review
12-244 Staple Home SensorThe Staple Head Home Sensor never turn on within 200ms after the STAPLER MOTOR
started to revolve backward (open).ProcedureEnter dC330 [012-207] and press Start.  Turn the Staple Head Home Sensor on/off using
paper. The display changes.
YN
+5 VDC is measured between the Stapler Assembly p/j (+) and Finisher PWB Chas-
sis (-).
YN
+5 VDC is measured between the Finisher PWB p/j (+) and Finisher PWB Chas-...

6/02
2-206DC1632/2240
12-244
Prelaunch Training/Review Status Indicator RAPsFigure 3 Stapler Assembly Logic Power CD
Figure 4 Finisher PWB 

6/02
2-207 DC1632/2240Status Indicator RAPs Prelaunch Training/Review
12-252  Front Tamperï With the Front Tamper Home Sensor off the Front Tamper Home Sensor did not turn on
within 800ms after move to the Front Tamper Home position has begun.
ï With the Front Tamper Home Sensor on The Front Tamper Sensor did not turn off when
the Front Tamper Home Sensor is deactuating.ProcedureEnter dC330 [012-091] (front) or [12-094] (rear) and press Start.   The Front Tamper Guide
moves.
YN
The Front Tamper Motor...

6/02
2-208DC1632/2240 Prelaunch Training/Review Status Indicator RAPsFigure 3 Front Tamper Motor CD
Figure 4 Finisher PWB 

6/02
2-209 DC1632/2240
12-253
Status Indicator RAPs Prelaunch Training/Review
12-253 Rear Tamperï With the Rear Tamper Home Sensor off The Rear Tamper Home Sensor did not turn on
within 800ms after move to the Rear Tamper Home position has begun.
ï With the Rear Tamper Home Sensor on: The Rear Tamper Home Sensor did not turn off
when the Rear Tamper Home Sensor is deactuating.ProcedureEnter dC330 [012-010] (front) or [12-013] (rear) and press Start.   The Rear Tamper Guide
energizes.
YN
The Rear Tamper...

6/02
2-210DC1632/2240
12-253
Prelaunch Training/Review Status Indicator RAPsFigure 4 Finisher PWB