Xerox 1632 2240 3535 Color Carrera Manual

6/02
2-181 DC1632/2240
10-348
Status Indicator RAPs Prelaunch Training/ReviewFigure 2 Fuser Main Heater and Sub Heater CD 

6/02
2-182DC1632/2240
10-349
Prelaunch Training/Review Status Indicator RAPs
10-349 Front Thermistor OpenThe machine logic detected an open circuit in the Front Thermistor.ProcedureTurn off the power, remove the Fuser Assembly, and allow it to cool down.
Measure the resistance between P/J600-4 and P/J600-6 on the Fuser Assembly. The resis-
tance is between 30 and 190 K Ohmís. 
YN
Check the Front Thermistor for an open circuit and poor contact. If no problems are found,
replace the Sensor Assembly (PL...

6/02
2-183 DC1632/2240
10-350
Status Indicator RAPs Prelaunch Training/Review
10-350 Sub Heater Over HeatThe Rear Thermistor detected an over heat condition.ProcedureNOTE: To clear this fault, re-set the value of dC131 [744-003] to 0. 
Turn off the power, remove the Fuser Assembly and allow it to cool down.
Measure the resistance between P/J600-7 and P/J600-9 on the Fuser Assembly.
  The resistance is between 30 and 190 K Ohmís. 
YN
Check the Rear Thermistor for an open circuit and poor contact. If the...

6/02
2-184DC1632/2240
10-351
Prelaunch Training/Review Status Indicator RAPs
10-351 Rear Thermistor OpenThe machine logic detected an open circuit in the Rear Thermistor.ProcedureTurn off the power, remove the Fuser Assembly and allow it to cool down.
Measure the resistance between P/J600-7 and P/J600-9 on the Fuser Assembly. The resis-
tance is between 30 and 190 K Ohmís. 
YN
Check the Rear Thermistor for an open circuit and poor contact. If the check is OK,
replace the Sensor Assembly (PL 7.2)....

6/02
2-185 DC1632/2240
10-352
Status Indicator RAPs Prelaunch Training/Review
10-352 Main Heater Warm Up The temperature did not reach the READY temperature within the specified time.ProcedureTurn off the power, remove the Fuser Assembly. and allow it to cool down.
Measure the resistance between P/J600-4 and P/J600-6 on the Fuser Assembly.
  The resistance is between 30 and 190 K Ohmís. 
YN
Check the Front Thermistor for an open circuit and poor contact. If the check is OK,
replace the Sensor Assembly...

6/02
2-186DC1632/2240
10-352
Prelaunch Training/Review Status Indicator RAPsFigure 2 Fuser Main Heater and Sub Heater CD 

6/02
2-187 DC1632/2240
10-353
Status Indicator RAPs Prelaunch Training/Review
10-353 Main Heater On TimeThe Main Heater remained on for more than the specified time.ProcedureTurn off the power, remove the Fuser Assembly. and allow it to cool down.
Measure the resistance between P/J600-4 and P/J600-6 on the Fuser Assembly.
  The resistance is between 30 and 190 K Ohmís. 
YN
Check the Front Thermistor for an open circuit and poor contact. If the check is OK,
replace the Sensor Assembly (PL 7.2).
Measure...

6/02
2-188DC1632/2240
10-353
Prelaunch Training/Review Status Indicator RAPsFigure 2 Fuser Main Heater and Sub Heater CD 

6/02
2-189 DC1632/2240
10-354
Status Indicator RAPs Prelaunch Training/Review
10-354 Sub Heater Warm UpThe temperature did not reach the READY temperature.ProcedureNOTE: To clear this fault, re-set the value of 
dC131-744-003 to 0. 
Turn off the power, remove the Fuser Assembly. and allow it to cool down. Measure the resis-
tance between P/J600-4 and P/J600-6 on the Fuser Assembly. The resistance is between 30
and 190 K Ohmís. 
YN
Check the Front Thermistor for an open circuit and poor contact. If the...

6/02
2-190DC1632/2240
10-356
Prelaunch Training/Review Status Indicator RAPs
10-356 Sub Heater On TimeThe Sub Heater remained on for more than the specified time.ProcedureTurn off the power, remove the Fuser Assembly. and allow it to cool down.
Measure the resistance between P/J600-7 and P/J600-9 on the Fuser Assembly. The resis-
tance is between 30 and 190 K Ohmís. 
YN
Check the Rear Thermistor for an open circuit and poor contact. If the check is OK,
replace the Sensor Assembly (PL 7.2).
Measure the...