Xerox 1632 2240 3535 Color Carrera Manual
Here you can view all the pages of manual Xerox 1632 2240 3535 Color Carrera Manual. The Xerox manuals for All in One Printer are available online for free. You can easily download all the documents as PDF.
Page 161
6/02 2-131 DC1632/2240 8-622, 8-623 Status Indicator RAPs Prelaunch Training/Review 8-622 Regicon Data Overflow (A1 Patch X)At A1 patch detection, the XSO correction setting value for either Y, M, C, or K exceeds the set- ting range (NVM value 0 to 472). NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK. YN Replace as required. Perform DC685 Color Registration (ADJ 9.6). 8-623 Regicon Data Overflow (A2...
Page 162
6/02 2-132DC1632/2240 8-624, 8-625 Prelaunch Training/Review Status Indicator RAPs 8-624 Regicon Data Overflow (Patch Magnification)MAG Adjusted Set Point of operation results for each of Y,M,C exceeded the set range (NVM value: 0~1432). NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK. YN Replace as required. Go to ADJ 9.6 Color Registration dC685. 8-625 Regicon Sample Block (A1 Patch-rear)At A1 (IN)...
Page 163
6/02 2-133 DC1632/2240 8-626, 8-627 Status Indicator RAPs Prelaunch Training/Review 8-626 Regicon Sample Block (A1 Patch-front)At A1 (OUT) patch detection, the number of the sample blocks does not reach the specified number. NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK. YN Replace as required. Perform DC685 Color Registration (ADJ 9.6). 8-627 Regicon Sample Lateral (A1 Patch-rear)At A1 (IN) patch...
Page 164
6/02 2-134DC1632/2240 8-628, 8-629 Prelaunch Training/Review Status Indicator RAPs 8-628 Regicon Sample Lateral (A1 Patch-front)At A1 (OUT) patch detection, the scan position of CYAN color that is the standard for the rest is incorrect. (Against the MOB SENSOR, the center position of the CYAN pattern is shifted by ±500µm or more.? NOTE: Status Code not displayed on UI. Machine operation continues.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK. YN Replace as...
Page 165
6/02 2-135 DC1632/2240 8-630, 8-631 Status Indicator RAPs Prelaunch Training/Review 8-630 Regicon Skew (Patch M)During A1 Patch detection, skew deviation for M exceeded tolerance. NOTE: Machine operation continues. Status Code not displayed on UI. Status Code logged in History.Initial ActionsClean MOB Sensor.ProcedureCheck the IBT Belt and Drum for a scratch or contamination. The check is OK. YN Replace as required. Perform DC685 Color Registration (ADJ 9.6). 8-631 Regicon Skew (Patch K)During A1 Patch...
Page 166
6/02 2-136DC1632/2240 8-900 Prelaunch Training/Review Status Indicator RAPs 8-900 Static JamWhen the machine power is turned off then on before a paper path fault is cleared, an 8-900 fault will be displayed. A voltage drop or interruption can also cause this fault. Initial Actionsï Check the entire paper path for paper or obstructions. ï Clean all the paper path sensors. ï Check the Fault History for the last paper path fault. Go to that paper path fault RAP. ProcedureIn sequence, enter the following...
Page 167
![Page 167
6/02
2-137 DC1632/2240
9-342
Status Indicator RAPs Prelaunch Training/Review
9-342 2nd BTR ContactThe 2nd BTR did not reach the contact position.Initial Actionsï Clean the 2nd BTR Retract Sensor and check for damage.
ï Check the 2nd BTR transmission gears for breakage.ProcedureIn sequence, enter the following: dC330 [009-051] then dC330 [009-052]. The 2nd BTR con-
tacts and retracts.
YN
Go to OF 99-6 Motor Open RAP.
Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 2ND BTR Retract Sensor
Figure 2 2ND BTR...](http://img.usermanuals.tech/thumb/82/49005/w300_xerox-1632-2240-3535-color-carrera-service-manual-166.png "Page 167
6/02
2-137 DC1632/2240
9-342
Status Indicator RAPs Prelaunch Training/Review
9-342 2nd BTR ContactThe 2nd BTR did not reach the contact position.Initial Actionsï Clean the 2nd BTR Retract Sensor and check for damage.
ï Check the 2nd BTR transmission gears for breakage.ProcedureIn sequence, enter the following: dC330 [009-051] then dC330 [009-052]. The 2nd BTR con-
tacts and retracts.
YN
Go to OF 99-6 Motor Open RAP.
Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 2ND BTR Retract Sensor
Figure 2 2ND BTR...")
6/02 2-137 DC1632/2240 9-342 Status Indicator RAPs Prelaunch Training/Review 9-342 2nd BTR ContactThe 2nd BTR did not reach the contact position.Initial Actionsï Clean the 2nd BTR Retract Sensor and check for damage. ï Check the 2nd BTR transmission gears for breakage.ProcedureIn sequence, enter the following: dC330 [009-051] then dC330 [009-052]. The 2nd BTR con- tacts and retracts. YN Go to OF 99-6 Motor Open RAP. Go to OF 99-2 Transmissive Sensor RAP. Figure 1 2ND BTR Retract Sensor Figure 2 2ND BTR...
Page 168
![Page 168
6/02
2-138DC1632/2240
9-343
Prelaunch Training/Review Status Indicator RAPs
9-343 2nd BTR RetractThe 2nd BTR did not reach the retract position.Initial Actionsï Clean the 2nd BTR Retract Sensor and check for damage.
ï Check the 2nd BTR transmission gears for breakage.ProcedureIn sequence, enter the following: dC330 [009-051] then dC330 [009-052]. The 2BTR contacts
and retracts.
YN
Go to OF 99-6 Motor Open RAP.
Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 2ND BTR Retract Sensor
Figure 2 2ND BTR...](http://img.usermanuals.tech/thumb/82/49005/w300_xerox-1632-2240-3535-color-carrera-service-manual-167.png "Page 168
6/02
2-138DC1632/2240
9-343
Prelaunch Training/Review Status Indicator RAPs
9-343 2nd BTR RetractThe 2nd BTR did not reach the retract position.Initial Actionsï Clean the 2nd BTR Retract Sensor and check for damage.
ï Check the 2nd BTR transmission gears for breakage.ProcedureIn sequence, enter the following: dC330 [009-051] then dC330 [009-052]. The 2BTR contacts
and retracts.
YN
Go to OF 99-6 Motor Open RAP.
Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 2ND BTR Retract Sensor
Figure 2 2ND BTR...")
6/02 2-138DC1632/2240 9-343 Prelaunch Training/Review Status Indicator RAPs 9-343 2nd BTR RetractThe 2nd BTR did not reach the retract position.Initial Actionsï Clean the 2nd BTR Retract Sensor and check for damage. ï Check the 2nd BTR transmission gears for breakage.ProcedureIn sequence, enter the following: dC330 [009-051] then dC330 [009-052]. The 2BTR contacts and retracts. YN Go to OF 99-6 Motor Open RAP. Go to OF 99-2 Transmissive Sensor RAP. Figure 1 2ND BTR Retract Sensor Figure 2 2ND BTR...
Page 169
![Page 169
6/02
2-139 DC1632/2240
9-348
Status Indicator RAPs Prelaunch Training/Review
9-348 1st BTR ContactThe 1st BTR did not reach the contact position.Initial Actionsï Clean the 1st BTR Retract Sensor and check for damage
ï Check the 1st BTR transmission gears for breakage
ProcedureIn sequence, enter the following: dC330 [009-054] then dC330 [009-055]. The 1st BTR con-
tacts and retracts.
YN
Go to OF 99-6 Motor Open RAP.
Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 1ST BTR Retract Sensor
Figure 2 1ST BTR...](http://img.usermanuals.tech/thumb/82/49005/w300_xerox-1632-2240-3535-color-carrera-service-manual-168.png "Page 169
6/02
2-139 DC1632/2240
9-348
Status Indicator RAPs Prelaunch Training/Review
9-348 1st BTR ContactThe 1st BTR did not reach the contact position.Initial Actionsï Clean the 1st BTR Retract Sensor and check for damage
ï Check the 1st BTR transmission gears for breakage
ProcedureIn sequence, enter the following: dC330 [009-054] then dC330 [009-055]. The 1st BTR con-
tacts and retracts.
YN
Go to OF 99-6 Motor Open RAP.
Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 1ST BTR Retract Sensor
Figure 2 1ST BTR...")
6/02 2-139 DC1632/2240 9-348 Status Indicator RAPs Prelaunch Training/Review 9-348 1st BTR ContactThe 1st BTR did not reach the contact position.Initial Actionsï Clean the 1st BTR Retract Sensor and check for damage ï Check the 1st BTR transmission gears for breakage ProcedureIn sequence, enter the following: dC330 [009-054] then dC330 [009-055]. The 1st BTR con- tacts and retracts. YN Go to OF 99-6 Motor Open RAP. Go to OF 99-2 Transmissive Sensor RAP. Figure 1 1ST BTR Retract Sensor Figure 2 1ST BTR...
Page 170
![Page 170
6/02
2-140DC1632/2240
9-349
Prelaunch Training/Review Status Indicator RAPs
9-349 1st BTR RetractThe 1st BTR did not reach the retract position.Initial Actionsï Clean the 1st BTR Retract Sensor and check for damage
ï Check the 1st BTR transmission gears for breakage
ProcedureIn sequence, enter the following: dC330 [009-054] then dC330 [009-055]. The 1st BTR con-
tacts and retracts.
YN
Go to OF 99-6 Motor Open RAP.
Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 1ST BTR Retract Sensor
Figure 2 1ST BTR...](http://img.usermanuals.tech/thumb/82/49005/w300_xerox-1632-2240-3535-color-carrera-service-manual-169.png "Page 170
6/02
2-140DC1632/2240
9-349
Prelaunch Training/Review Status Indicator RAPs
9-349 1st BTR RetractThe 1st BTR did not reach the retract position.Initial Actionsï Clean the 1st BTR Retract Sensor and check for damage
ï Check the 1st BTR transmission gears for breakage
ProcedureIn sequence, enter the following: dC330 [009-054] then dC330 [009-055]. The 1st BTR con-
tacts and retracts.
YN
Go to OF 99-6 Motor Open RAP.
Go to OF 99-2 Transmissive Sensor RAP.
Figure 1 1ST BTR Retract Sensor
Figure 2 1ST BTR...")
6/02 2-140DC1632/2240 9-349 Prelaunch Training/Review Status Indicator RAPs 9-349 1st BTR RetractThe 1st BTR did not reach the retract position.Initial Actionsï Clean the 1st BTR Retract Sensor and check for damage ï Check the 1st BTR transmission gears for breakage ProcedureIn sequence, enter the following: dC330 [009-054] then dC330 [009-055]. The 1st BTR con- tacts and retracts. YN Go to OF 99-6 Motor Open RAP. Go to OF 99-2 Transmissive Sensor RAP. Figure 1 1ST BTR Retract Sensor Figure 2 1ST BTR...