Xerox 1632 2240 3535 Color Carrera Manual

6/02
2-101 DC1632/2240
7-110
Status Indicator RAPs Prelaunch Training/ReviewFigure 3 Takeaway Motor 1 CD 

6/02
2-102DC1632/2240
7-115
Prelaunch Training/Review Status Indicator RAPs
7-115 Tray 3 MisfeedThe Take Away Sensor does not detect paper after feeding from Tray 3.Initial Actionsï Check condition and specification of paper in Tray 3.
ï Check the paper path for obstructions.
ï Check for wear and clean the Tray 3 Feeder Roll, Take Away Roll and the Nudger Roll.ProcedureEnter dC330 [008-102] and press Start.  Block and unblock the Tray 3 Feed Out Sensor (PL
15.10).  The display changes.
YN
Go to OF 99-2...

6/02
2-103 DC1632/2240
7-115
Status Indicator RAPs Prelaunch Training/ReviewFigure 3 Takeaway Motor 1 CD 

6/02
2-104DC1632/2240
7-119
Prelaunch Training/Review Status Indicator RAPs
7-119 Tray 4 MisfeedThe Feed Out Sensor does not detect paper after feeding from Tray 4.Initial Actionsï Check condition and specification of paper in Tray 4.
ï Check the paper path for obstructions.
ï Check for wear and clean the Tray 4 Feeder Roll, Take Away Roll and the Nudger Roll.ProcedureEnter dC330 [008-103] and press Start.  Block and unblock the Tray 4 Feed out Sensor (PL
16.5).  The display changes.
YN
Go to OF 99-2...

6/02
2-105 DC1632/2240
7-119
Status Indicator RAPs Prelaunch Training/ReviewFigure 3 Takeaway Motor 2 CD 

6/02
2-106DC1632/2240
7-122
Prelaunch Training/Review Status Indicator RAPs
7-122 Tray 4 OpenedThe Tray 4 Feed Out Sensor detected paper when Tray 4 is pulled out and pushed in during a
print.Initial Actionsï Check condition and specification of paper in Tray 4.
ï Check the paper path for obstructions and clean the Tray 4 Feed out Sensor.
ï Check the Tray 4 mechanical operation.ProcedureEnter dC330 [008-103] and press Start.  Block and unblock the Tray 4 Feed out Sensor (PL
16.5).  The display changes....

6/02
2-107 DC1632/2240
7-250
Status Indicator RAPs Prelaunch Training/Review
7-250 Tray CommunicationCommunication fault between Tray Module PWB and MCU PWB.ProcedureThere is +5 VDC measured at P/J541-9 on the Tray Module PWB (PL 15.9).
YN
Check the wires and connectors. If the check is OK, replace the MCU PWB (PL 13.1). 
If the problem continues, replace the I/F PWB (PL 13.1)CAUTION
ESS PWB and MCU PWB cannot be replaced at the same time.
Check the wires and connectors. If the check is OK, replace the...

6/02
2-108DC1632/2240
7-252, 7-270
Prelaunch Training/Review Status Indicator RAPs
7-252 Out Module LogicIncorrect software data was detected.ProcedureSwitch the power off then on. The problem continues. 
YN
Return to Service Call Procedures.
Reinstall the software. 
If the problem continues, replace the MCU PWB (PL 13.1).
7-270 Tray 1 Paper Size SensorAn abnormal AD value was detected by the Tray 1 Paper Size Sensor.Initial ActionsEnsure that the Paper Guide Tab makes contact with the...

6/02
2-109 DC1632/2240
7-271, 7-274
Status Indicator RAPs Prelaunch Training/Review
7-271 Tray 2 Paper Size SensorAn abnormal AD value was detected by the Tray 2 Paper Size Sensor.Initial ActionsEnsure that the Paper Guide Tab makes contact with the sensor.ProcedureEnsure that Tray 2 is fully seated. The voltages measured at P/J546-8 on the Tray Module
PWB corresponds with the table on BSD 7.2
YN
There is +5VDC measured between P/J816-1 and 3 on the Tray 2 Paper Size Sensor. 
YN
Check the wires and...

6/02
2-110DC1632/2240
7-276, 7-277
Prelaunch Training/Review Status Indicator RAPs
7-276 Tray 3 Paper Size SensorAn abnormal AD value was detected by the Tray 3 Paper Size Sensor.Initial ActionsEnsure that the Paper Guide Tab makes contact with the sensor.ProcedureEnsure that Tray 3 is fully seated. The voltages measured at P/J548-11 on the Tray Module
PWB corresponds with the table on BSD 7.4
YN
There is +5VDC measured between P/J820-1 and 3 on the Tray 3 Paper Size Sensor
(PL 16.1). 
YN
Check the wires...