Xerox 1632 2240 3535 Color Carrera Manual

6/02
2-141 DC1632/2240
9-350
Status Indicator RAPs Prelaunch Training/Review
9-350 IBT Home SensorThe IBT Home Sensor detected the IBT position strip before the IBT Belt made a complete rev-
olution.Initial Actionsï Clean the IBT Home Sensor and check for damage
ï Check the IBT drives for damage.ProcedureEnter dC330 [004-002]. The IBT Motor energizes. 
YN
Go to OF 99-6 Motor Open RAP.Enter dC330 [004-414] then enter dC330 [004-002]. The display changes state. 
YN
Go to OF 99-2 Transmissive Sensor RAP....

6/02
2-142DC1632/2240
9-351
Prelaunch Training/Review Status Indicator RAPs
9-351 Drive LogicThe IBT Edge Sensor detected that the IBT Belt is not tracking correctly.Initial Actionsï Check the IBT Edge Sensor for damage. Ensure that the actuator is touching the edge of
the belt.
ï Check the IBT steering drives for damage.ProcedureSwitch on the power. There is +1VDC to +3VDC from P/J 533-A11 to GND. 
YN
There is +5VDC measured between P/J533-A10 and P/J533-A9 on the I/F PWB. 
YN
Replace the MCU PWB (PL...

6/02
2-143 DC1632/2240
9-358, 9-360
Status Indicator RAPs Prelaunch Training/Review
9-358 Full Toner SensorThe Full Toner Sensor detects a full toner condition.Initial Actionsï Ensure that the Waste Toner Cartridge is not full.
ï Check the sensor for toner contamination and foreign substances.ProcedureRemove the Full Toner Sensor from the bottle. Enter dC330 [009-150]. Block and unblock the
Full Toner Sensor (PL 4.1).  The display changes state.
YN
Go to OF 99-2 Transmissive Sensor RAP.
 Replace the MCU...

6/02
2-144DC1632/2240
9-361, 9-362
Prelaunch Training/Review Status Indicator RAPs
9-361 Magenta Drum Cartridge CommunicationA communication failure with Magenta Drum Cartridge was detected.Initial ActionsCheck that the Magenta Drum Cartridge is seated correctly.ProcedureEnter dC330 [009-152, Drum (M) Data]. The display is H.
YN
Check the wires and connectors. If the check is OK, replace the Magenta Drum Cartridge
(refer to Section 6, Machine Consumables). 
Replace the MCU PWB. (PL 13.1).
Figure 1 Drum M...

6/02
2-145 DC1632/2240
9-363, 9-380
Status Indicator RAPs Prelaunch Training/Review
9-363 Black Drum Cartridge CommunicationA communication failure with the Black Drum Cartridge was detected.Initial ActionsCheck that the Black Drum Cartridge is seated correctly.ProcedureEnter dC330 [009-154, Drum (K) Data]. The display is H.
YN
Check the wires and connectors. If the check is OK, replace the Black Drum Cartridge
(refer to Section 6, Machine Consumables).
Replace the MCU PWB (PL 13.1).
Figure 1 Drum K...

6/02
2-146DC1632/2240
9-381, 9-382
Prelaunch Training/Review Status Indicator RAPs
9-381 ATC Sensor (M)The ATC Sensor (M) detects a low TC (toner concentration)Initial Actionsï Check that Toner/Developer is present.
ï Check the ATC Sensor (M) for contamination. Ensure that the sensor is seated correctly.ProcedureNOTE: To clear this fault, enter dC131 and set the value of NVM location 752-110 to 0. 
Record the value in NVM location 752-324, then set the value to 1. Perform ADJ 9.3. After the
measurement...

6/02
2-147 DC1632/2240
9-383, 9-390
Status Indicator RAPs Prelaunch Training/Review
9-383 ATC Sensor (K)The ATC Sensor (K) detects an insufficient amount of developer materialInitial Actionsï Check that Toner/Developer is present.
ï Check the ATC Sensor (K) for contamination. Ensure that the sensor is seated correctly.ProcedureNOTE: To clear this fault, enter dC131 and set the value of NVM location 752-110 to 0. 
Record the value in NVM location 752-324, then set the value to 1. Perform ADJ 9.3. After...

6/02
2-148DC1632/2240
9-391, 9-392
Prelaunch Training/Review Status Indicator RAPs
9-391 New Toner Cartridge (C)The New Cartridge Detect Switch (C) was not engaged to reset the Accumulative Dispense
time NVM value to 0 when a new cartridge was installed.Initial Actionsï Re-install the Toner Cartridge ensuring that the Dispense Motor and the Toner Cartridge
is engaged.
ï Check that the New/Old Detection Switch (metal part) at the rear of the Toner Cartridge is
raised. If the New/Old Detection Switch is...

6/02
2-149 DC1632/2240
9-393, 9-408
Status Indicator RAPs Prelaunch Training/Review
9-393 New Toner Cartridge (Y)When a new Toner Cartridge was installed, the level of the New Cartridge Detect Switch (Y)
remained L when it should be changed to H by the Dispense Motor drive.Initial Actionsï Re-install the Toner Cartridge ensuring that the Dispense Motor and the Toner Cartridge
is engaged.
ï Check that the New/Old Detection Switch (metal part) at the rear of the Toner Cartridge is
raised. If the New/Old...

6/02
2-150DC1632/2240
9-410
Prelaunch Training/Review Status Indicator RAPs
9-410 Toner Cartridge (Y) Near EmptyThe Yellow Toner Cartridge is nearly empty/empty.
NOTE: Continuous running of high density prints can temporarily deplete the toner supply.Initial Actionsï Ensure that there is toner and the toner is evenly distributed in the cartridge (Y).
ï Check the ATC Sensor (Y) for blockage or contaminants.
ï Check the drive system from the Developer Drive Motor to the Developer Housing (Y) for
damage....