Xerox 1632 2240 3535 Color Carrera Manual

6/02
2-171 DC1632/2240
9-930, 9-931
Status Indicator RAPs Prelaunch Training/Review
9-930 Black Drum Cartridge Not DetectedThe machine logic detected that Black Drum Cartridge is not installed. Initial Actionsï Ensure Black Drum Cartridge is installed correctly.
ï Switch the power off, then on.ProcedureSwap Black Drum Cartridge with Drum (Y), (C) or (M). The problem is corrected.
YN
Check that P/J-405 on the MCU PWB and P/J-622 are connected and the wires for an
open or short. If the check is OK, replace...

6/02
2-172DC1632/2240
9-932, 9-933
Prelaunch Training/Review Status Indicator RAPs
9-932 Magenta Drum Cartridge Not DetectedThe machine logic detected that Magenta Drum Cartridge is not installed. Initial Actionsï Ensure Magenta Drum Cartridge is installed correctly.
ï Switch the power off, then on.ProcedureSwap Magenta Drum Cartridge with Drum (Y), (C) or K). The problem is corrected.
YN
Check that P/J-405 on the MCU PWB and P/J-624 are connected and the wires for an
open or short. If the check is OK,...

6/02
2-173 DC1632/2240
10-105
Status Indicator RAPs Prelaunch Training/Review
10-105 Face Up Exit Sensor On The Face Up Exit Sensor did not energize.Initial Actionsï Check condition and specification of the paper supply.
ï Check for obstructions in the paper feed path.
ï Clean the Exit Roll and check for wear.
ï Check the drive transmissions for damage or wear.ProcedureEnter dC330 [010-103] and press Start. Block and unblock the Face Up Exit Sensor (PL 11.2).  
The display changes state.
YN
Go to OF 99-2...

6/02
2-174DC1632/2240
10-105
Prelaunch Training/Review Status Indicator RAPsFigure 4 The 2ND BTR Retract Motor CD 

6/02
2-175 DC1632/2240
10-106, 10-110Status Indicator RAPs Prelaunch Training/Review
10-106 Face Up Exit Sensor OffThe Face Up Exit Sensor did not de-energize. Initial Actionsï Check condition and specification of the paper supply.
ï Check for obstructions in the paper feed path.
ï Clean the Fuser Exit Roll and check for wear.
ï Check the drive transmissions for damage or wear.ProcedureEnter dC330 [010-103] and press Start.  Block and unblock the Face Up Exit Sensor (PL 11.2).  
The display changes...

6/02
2-176DC1632/2240
10-110
Prelaunch Training/Review Status Indicator RAPsFigure 2 Exit Gate Solenoid CD
Figure 3 Registration Clutch CD
Figure 4 2ND BTR Retract Motor 

6/02
2-177 DC1632/2240
10-111
Status Indicator RAPs Prelaunch Training/Review
10-111 Fuser Exit Switch Off (Face Down)The Fuser Exit Switch did not de-energize.Initial Actionsï Check condition and specification of the paper supply.
ï Check for obstructions in the paper feed path.
ï Clean the Fuser Exit Roll and check for wear.
ï Check the drive transmissions for damage or wear.ProcedureCheck the Fuser Stripper Fingers and Fuser Roll for dirt build up, wear or damage. The
check is OK.
YN
Clean or replace...

6/02
2-178DC1632/2240
10-125
Prelaunch Training/Review Status Indicator RAPs
10-125 Duplex Wait Sensor OnThe Duplex Wait Sensor did not energizeInitial Actionsï Check condition and specification of paper in Tray 2.
ï Check the paper path for obstructions.
ï Check for wear and clean the Duplex Drive Rolls.
ï Check the exit transmission gears for breakage and wear.ProcedureEnter dC330 [008-105] and press Start.  Block and unblock the Duplex Wait Sensor (PL 12.2). 
The display changes state.
YN
Go to OF...

6/02
2-179 DC1632/2240
10-125
Status Indicator RAPs Prelaunch Training/ReviewFigure 2 Duplex Motor CD
Figure 3 Duplex Exit Gate SolenoidFigure 4 Inverter Forward Clutch CD 

6/02
2-180DC1632/2240
10-125, 10-348
Prelaunch Training/Review Status Indicator RAPsFigure 5 Inverter Reverse Clutch CD
10-348 Main Heater Over HeatThe Front Thermistor detected an overheat condition.ProcedureNOTE: To clear this fault, re-set the value of dC131 [744-003] to 0. 
Turn off the power, remove the Fuser Assembly. and allow it to cool down.
Measure the resistance between P/J600-4 and P/J600-6 on the Fuser Assembly.
  The resistance is between 30 and 190 K Ohmís. 
YN
Check the Front Thermistor...