Xerox 1632 2240 3535 Color Carrera Manual

6/02
2-191 DC1632/2240
10-356
Status Indicator RAPs Prelaunch Training/ReviewFigure 2 Fuser Main Heater and Sub Heater CD 

6/02
2-192DC1632/2240
10-398
Prelaunch Training/Review Status Indicator RAPs
10-398 Fan LockThe machine logic detected a failure of the Fuser Fan, LVPS Fan or the Rear Fan.ProcedureEnter dC330 [004-050].  The Fuser Fan revolves at high speed.
YN
There is +24VDC measured at J222-4. 
YN
Check the wires and connectors. If the check is OK, replace the MCU PWB (PL
13.1).
With dC330 [004-050] entered, stack dC330 [004-200] and press Start. The display is H. 
YN
Check the wires and connectors. If the check is...

6/02
2-193 DC1632/2240
10-398
Status Indicator RAPs Prelaunch Training/ReviewFigure 3 The LPVS Fan CD 

6/02
2-194DC1632/2240
10-420, 10-421
Prelaunch Training/Review Status Indicator RAPs
10-420 Fuser Near End Of LifeReplace the Fuser Assembly in X copies.ProcedureThe Fuser Assembly was replaced.
YN
Replace the Fuser Assembly (PL 7.2) 
Run the dC135 [954-804]. The initial value is 0.
YN
Replace the MCU PWB (PL 13.1).
Ensure that the LIFE setting value is 100K, turn power OFF/ON.
If the problem continues, replace the MCU PWB (PL 13.1).
10-421 Fuser End Of LifeFuser at end of life.ProcedureThe Fuser...

6/02
2-195 DC1632/2240
12-100
Status Indicator RAPs Prelaunch Training/Review
12-100 H Transport Entrance Sensor OnThe H Transport Entrance Sensor does not detect paper within the specific time after the Reg-
istration Clutch (in IOT) actuated.ProcedureEnter dC330 [012-001] and press Start. The Finisher Drive Motor energizes.
YN
Press Stop.  Repair the drives as required (PL 17.7) for mechanical problems.  If the
drives are mechanically good, check the circuit of the Finisher Drive Motor (Figure 4).  +5...

6/02
2-196DC1632/2240
12-100
Prelaunch Training/Review Status Indicator RAPsFigure 4 Finisher Drive Motor CD
Figure 5 Finisher PWB 

6/02
2-197 DC1632/2240
12-102
Status Indicator RAPs Prelaunch Training/Review
12-102 H Transport Entrance Sensor OffPaper did not deactuate the H Transport Entrance Sensor.ProcedureOpen the H Transport.  Check H Transport Belts, H Transport Belt Drive Rolls, and Guides on
H Transport Cover for installation or damage problems. The components are good.
YN
Repair as required (PL 17.3, PL 17.4).
Rerun the job. The problem continues.
YN
Return to Service Call Procedures.
Replace the H Transport Entrance...

6/02
2-198DC1632/2240
12-104
Prelaunch Training/Review Status Indicator RAPs
12-104 H Transport Exit Sensor OnThe H Transport Exit Sensor did not detect paper within the specific time after the H Transport
Entrance Sensor has detected the paper. (The specified time differs depending on the paper
size.)ProcedureEnter dC330 [012-104] and press Start.  Actuate and deactuate the H Transport Exit Sensor.
The display changes.
YN
Repair the sensor as required (PL 17.4) for mechanical problems.  If the sensor...

6/02
2-199 DC1632/2240
12-106
Status Indicator RAPs Prelaunch Training/Review
12-106  H Transport Exit Sensor OffPaper did not deactuate the H Transport Exit Sensor.ProcedureEnter dC330 [012-217] and press Start. Actuate and deactuate the Decurler Cam Home Sen-
sor. The display changes.
YN
Check the circuit of the Decurler Cam Home Sensor (Figure 2). 
Enter dC330 [012-070] and press Start. The Decurler Cam Clutch energizes.
YN
Check the circuit of the Decurler Cam Clutch (Figure 3). 
Check the...

6/02
2-200DC1632/2240
12-120
Prelaunch Training/Review Status Indicator RAPs
12-120 Compiler Entrance Sensor OnThe Compiler Entrance Sensor did not detect paper.ProcedureEnter dC330 [012-101] and press Start.  Actuate and deactuate the Complier Entrance Sen-
sor. The display changes.
YN
Check the circuit of the Complier Entrance Sensor (Figure 2). 
Check the following:
ï Complier Entrance Sensor Actuator for breakage and bending
ï Paper path failure for burr and foreign substance.
ï Decurler Roll/pinch...