Xerox 1632 2240 3535 Color Carrera Manual

6/02
2-231 DC1632/2240
12-305
Status Indicator RAPs Prelaunch Training/ReviewFigure 3 Finisher PWB 

6/02
2-232DC1632/2240
12-350
Prelaunch Training/Review Status Indicator RAPs
12-350 Finisher CommunicationCommunication cannot be established between the MCU PWB and the Finisher PWB.ProcedureSwitch the power off then on.  CR7 on the Finisher PWB is lit.
YN
+24 VDC is measured between the Finisher PWB p/j (+) and Finisher PWB Chassis
(-).
YN
Check the +24VDC circuit to the Finisher PWB p/j by referring to Chapter 7 Wiring
Data ( Finisher +24VDC-1)
Replace the Finisher PWB (PL 17.13).
Switch off the...

6/02
2-233 DC1632/2240
12-399
Status Indicator RAPs Prelaunch Training/Review
12-399 Staple Mode LogicA paper size and staple mode that cannot be specified were specified.ProcedureReprogram job. 

6/02
2-234DC1632/2240
12-901
Prelaunch Training/Review Status Indicator RAPs
12-901 Power On H Transport Entrance SensorThe H Transport Entrance Sensor detected a paper at power on, when all the interlock were
closed, or at initialization.ProcedureCheck the following:
ï The Actuator for return failure
ï Enter dC330 [012-103]  and press Start.  Check only the signal wire of the sensor.
ï Check that the power voltage at the customer site does not drop.
Figure 1 Component Location
Figure 2 H Transport...

6/02
2-235 DC1632/2240
12-902
Status Indicator RAPs Prelaunch Training/Review
12-902 Power On H Transport Exit SensorThe H Transport Exit Sensor detected a paper at power on, when all the INTERLOCK were
closed, or at initialization.ProcedureCheck the following:
ï The Actuator for return failure
ï Enter dC330 [012-104]  and press Start.  Check only the signal wire of the sensor.
ï Check that the power voltage at the customer site does not drop.
Figure 1 Component Location
Figure 2 H Transport Sensor...

6/02
2-236DC1632/2240
12-903
Prelaunch Training/Review Status Indicator RAPs
12-903 Power On Compiler Entrance SensorThe Compiler Entrance Sensor detected a paper at power on, when all the INTERLOCK were
closed, or at initialization.ProcedureCheck the following:
ï The Actuator for return failure
ï Enter dC330 [012-101] and press Start.  Check only the signal wire of the sensor.
ï Check that the power voltage at the customer site does not drop.
Figure 1 Component Location
Figure 2 Compiler Entrance Sensor...

6/02
2-237 DC1632/2240
12-904
Status Indicator RAPs Prelaunch Training/Review
12-904 Power On Compiler Paper Sensorï The Compiler Paper Sensor continues to detect paper when the paper was output auto-
matically due to the power on initialization.
ï The Compiler Paper Sensor detected paper with no history of paper output to the Com-
piler Tray when all the interlocks were closed.ProcedureCheck the following:
ï The Actuator for return failure
ï Enter dC330 [012-102]  and press Start.  Check only the signal...

6/02
2-238DC1632/2240
12-910
Prelaunch Training/Review Status Indicator RAPs
12-910 Staple Feed Readyï At the staple preparation operation at initialization, the Staple Ready Sensor does not go
to ready (L) status after 13 times of stapling operation.
ï The Stapler Ready Sensor is turned off (H) just before the Staple.ProcedureRemove the Stapler Assembly with a connector connected.  Enter dC330 [012-209] and press
Start.  Actuate the Staple Ready Sensor. The display changes.
YN
+5 VDC is measured between...

6/02
2-239 DC1632/2240
12-910
Status Indicator RAPs Prelaunch Training/ReviewFigure 2 Staple Motor CD
Figure 3 Finisher PWB 

6/02
2-240DC1632/2240
12-911
Prelaunch Training/Review Status Indicator RAPs
12-911 Stacker Lower Safety WarningThe Height Alignment was not successful within 250ms during Tray lowering while stacking.ProcedureCheck the following:
This Fault Code is an operation message.  No need for servicing If the display of 012-911 has
not been cleared after removing paper in the Stacker Tray, check the following: 
ï The Actuators of the Stack Height Sensor for dragging and return failure.
ï Enter dC330 [012-201] and...