Xerox 1632 2240 3535 Color Carrera Manual

6/02
2-91 DC1632/2240
6-380
Status Indicator RAPs Prelaunch Training/Review
6-380 ROS SOS Y Length The interval of the ROS SOS (Y) signals exceeds the specified value.  ProcedureBSD 6.5 BSD 6.1
+5VDC is measured between the MCU PWB j401-b20 (+) and GND (-)   
YN
Replace the MCU PWB (PL 13.1)
Check the wire between the SOS PWB (Y) j516-1 and the MCU PWB j401 for an open circuit.  
Check the wire between the LD Drive (Y) j529 and the MCU PWB j401 for an open circuit.  
If no problems are found, replace the...

6/02
2-92DC1632/2240
6-381, 6-382
Prelaunch Training/Review Status Indicator RAPs
6-381 ROS SOS Length Fail MThe interval of the ROS SOS (M) signals exceeds the specified value.  ProcedureBSD 6.6 BSD 6.1
Check the voltage between j401-b20 (+) and GND (-) on MCU PWB. +5VDC is measured
between the MCU PWB j401-b20 (+) and GND (-). 
YN
Replace the MCU PWB (PL 13.1)
Check the wire between the SOS PWB (M) j517-1 and the MCU PWB j401 for an open circuit.  
Check the wire between the LD Drive M j528 and the MCU...

6/02
2-93 DC1632/2240
6-383, 6-385
Status Indicator RAPs Prelaunch Training/Review
6-383 ROS SOS K LengthThe interval of the ROS SOS (K) signals exceeds the specified value.  ProcedureBSD 6.8 BSD 6.1
Check the voltage between the MCU PWB j401-b20 (+) and GND (-). +5VDC is measured.
YN
Replace the MCU PWB (PL 13.1)
Check the wire between the SOS PWB (K) j515-1 and the MCU PWB j401 for an open circuit.  
Check the wire between the LD Drive K j526 and the MCU PWB j401 for an open circuit.  
If no problems...

6/02
2-94DC1632/2240
6-389
Prelaunch Training/Review Status Indicator RAPs
6-389 Carriage Over Run RightThe carriage has overrun at the Scan End.  ProcedureBSD 6.4 BSD 6.12A
Turn off the power.  Remove the Platen Glass.   Manually move the Full Rate Carriage. The
Carriage moves easily.
YN
Clear the Carriage Cable distortion, stranding, damage and foreign substance on the
CARRIAGE RAIL etc., causing the load.  
Turn on the power.  Enter dC330 [006-212] and press Start.   Manually move the Full Rate Car-...

6/02
2-95 DC1632/2240
6-390
Status Indicator RAPs Prelaunch Training/Review
6-390  Carriage Over Run LeftThe CRG has overrun at the Home End.  ProcedureBSD 6.4 BSD 6.12A
Turn off the power.  Remove the Platen Glass.  
Manually move the Full Rate Carriage.   The Carriage moves easily.
YN
Clear the Carriage Cable distortion, stranding, damage and foreign substance on the
CARRIAGE RAIL etc., causing the load.  
Turn on the power.  Enter dC330 [006-212] and press Start.  
Manually move the Full Rate Carriage...

6/02
2-96DC1632/2240
6-391
Prelaunch Training/Review Status Indicator RAPs
6-391  Scan Initialize Motor DriverThe Carriage Motor error was detected after the initialization was started.  ProcedureBSD 6.4 BSD 6.1
Turn off the power.  Remove the following covers:
ïTOP COVER
ï IIT REAR COVER
Measure conductivity of the following:
Between the Carriage Motor p739-6 and the IIT/IPS PWB j725-6
Between the Carriage Motor p739-6 and the IIT/IPS PWB j725-5
Between the Carriage Motor p739-4 and the IIT/IPS PWB...

6/02
2-97 DC1632/2240
7-104
Status Indicator RAPs Prelaunch Training/Review
7-104 Tray 1 Feed Out SensorThe Tray 1 Feed Out Sensor does not detect paper after feeding from Tray 1.Initial Actionsï Check condition and specification of paper in Tray 1.
ï Check the paper path for obstructions.
ï Check for wear and clean the Tray 1 Feeder Roll, Take Away Roll and the Nudger Roll.ProcedureEnter dC330 [008-100] and press Start. Block and unblock Tray 1 Feed Out Sensor (PL2.3).
The display changes.
YN
Go to OF...

6/02
2-98DC1632/2240
7-105
Prelaunch Training/Review Status Indicator RAPs
7-105 Tray 1 MisfeedThe Tray 1 Feed Out Sensor does not detect paper after feeding from Tray 1.Initial Actionsï Check condition and specification of paper in Tray 1.
ï Check the paper path for obstructions.
ï Check for wear and clean the Tray 1 Feed Roll, Take Away Roll and the Nudger Roll.ProcedureEnter dC330 [008-100] and press Start.  Block and unblock the Tray 1 Feed Out Sensor (PL
2.3).  The display changes.
YN
Go to OF 99-2...

6/02
2-99 DC1632/2240
7-105
Status Indicator RAPs Prelaunch Training/ReviewFigure 3 Takeaway Motor 1 CD 

6/02
2-100DC1632/2240
7-110
Prelaunch Training/Review Status Indicator RAPs
7-110 Tray 2 MisfeedThe Take Away Sensor does not detect paper after feeding from Tray 2.Initial Actionsï Check condition and specification of paper in Tray 2.
ï Check the paper path for obstructions.
ï Check for wear and clean the Tray 2 Feeder Roll, Take Away Roll and the Nudger Roll.ProcedureEnter dC330 [008-106] and press Start.  Block and unblock the Take Away Sensor (PL 16.6). 
The display changes.
YN
Go to OF 99-2...