Xerox 1632 2240 3535 Color Carrera Manual

6/02
2-41 DC1632/2240
3-951, 3-952
Status Indicator RAPs Prelaunch Training/Review
3-951 Tray 2 No PaperNo paper in Tray 2ProcedureEnter dC330 [007-121] and press Start. Actuate Tray 2 No Paper Sensor.  Display changes
state.
YN
Go to OF 99-2 Transmissive Sensor RAP, repair Tray 2 No Paper Sensor (PL 15.3, PL
16.7). 
Replace MCU PWB (PL 13.1). 
Figure 1 Tray 2 No Paper Sensor CD
3-952 Tray 3 No PaperNo paper in Tray 3ProcedureEnter dC330 [007-122] and press Start. Actuate Tray 3 No Paper Sensor.  Display...

6/02
2-42DC1632/2240
3-953, 3-954
Prelaunch Training/Review Status Indicator RAPs
3-953 Tray 4 No PaperNo paper in Tray 4.ProcedureEnter dC330 [007-123] and press Start. Actuate Tray 4 No Paper Sensor.  Display changes
state.
YN
Go to OF 99-2 Transmissive Sensor RAP, repair Tray 4 No Paper Sensor (PL 15.7, PL
16.1). 
Replace MCU PWB (PL 13.1). 
Figure 1 Tray 4 No Paper Sensor CD
3-954 Tray 5 EmptyTray 5 is empty.ProcedureEnter dC330 [007-125] and press Start. Actuate the Tray 5 No Paper Sensor.  Display...

6/02
2-43 DC1632/2240
3-958, 3-959
Status Indicator RAPs Prelaunch Training/Review
3-958 Tray 5 Paper Size MismatchThe paper in the Tray 5 does not match the paper size selected.ProcedureThe correct size paper is loaded in Tray 5.
YN
Load the correct size paper and return to Service Call Procedures.
Go to RAP 7-954.
3-959 Tray 1 Paper Size MismatchThe paper in Tray 1 does not match the paper size selected.ProcedureThe correct size paper is loaded in Tray 1.
YN
Load the correct size paper and return to...

6/02
2-44DC1632/2240
3-960, 3-961
Prelaunch Training/Review Status Indicator RAPs
3-960 Tray 2 Paper Size MismatchThe paper in Tray 2 does not match the paper size selected.ProcedureThe correct size paper is loaded in Tray 2.
YN
Load the correct size paper and return to Service Call Procedures.
Go to  RAP 7-271.
3-961 Tray 3 Paper Size MismatchThe paper in Tray 3 does not match the paper size selected.ProcedureThe correct size paper is loaded in Tray 3.
YN
Load the correct size paper and return to...

6/02
2-45 DC1632/2240
3-962, 3-965
Status Indicator RAPs Prelaunch Training/Review
3-962 Tray 4 Paper Size MismatchThe paper in Tray 4 does not match the paper size selected.ProcedureThe correct size paper is loaded in Tray 4.
YN
Load the correct size paper and return to Service Call Procedures.
Go to RAP 7-277.
3-965 No PaperThe paper does not match the paper size selected.ProcedureThe correct size paper is loaded.
YN
Load the correct size paper and return to Service Call Procedures.
Go to the...

6/02
2-46DC1632/2240
3-971, 3-972
Prelaunch Training/Review Status Indicator RAPs
3-971 MagnificationIncompatible MagnificationProcedureSwitch the power off then on.   The problem continues.
YN
Return to Service Call Procedures.
Change parameters and rerun job.
3-972 Over Number of Document Pages Stored ProcedureSwitch the power off then on. The problem is corrected. 
YN
Set the number of document pages to the maximum count.
Return to Service Call Procedures. 

6/02
2-47 DC1632/2240
3-980, 3-985
Status Indicator RAPs Prelaunch Training/Review
3-980 Stapler Position ErrorThe Stapler is not available at the specified position.ProcedureSwitch the power off then on. The problem is corrected. 
YN
Re-set the parameters.
Return to Service Call Procedures.
3-985 Tray 5 Pause CheckThe SMH tray jamed.ProcedureSwitch the power off then on. The problem is corrected. 
YN
Go to RAP 7-794.
Return to Service Call Procedures. 

6/02
2-48DC1632/2240
3-986
Prelaunch Training/Review Status Indicator RAPs
3-986 Print Completion ErrorThe number of spooled pages does not match the output.ProcedureSwitch the power off then on. The problem is corrected. 
YN
Count the number of prints to ensure job integrity.
Return to Service Call Procedures. 

6/02
2-49 DC1632/2240
4-340
Status Indicator RAPs Prelaunch Training/Review
4-340 IOT RAMMCU PWB RAM test failed.ProcedureSwitch the power off then on.  The problem continues.
YN
Return to Service Call Procedures.
Replace  the MCU PWB (PL 13.1).   
If the problem continues, replace the MCU NVM PWB (PL 13.1).  

6/02
2-50DC1632/2240
4-341, 4-342
Prelaunch Training/Review Status Indicator RAPs
4-341 IOT LogicOperation failure of an  MCU PWB operation.Initial ActionsRe-installation the software.ProcedureCH3.1A, CH3.6A
Connect black meter lead to ground or machine frame.  There is +5VDC measured at J401-
B20 
YN
There is +5VDC measured at j568-5 
YN
 There is +5VDC measured at j568-1 
YN
Repair the wire between FS534 and j568-2. 
Replace ROS Assembly (PL 3.1). 
Check for an open circuit between j568-5 the p400-9....