Vodavi Starplus Spd 4896 Hybrid Key Telephone System Installation Manual

EXCEPTlON TABLES PROGRAMMING
STARPLUS @ SPD 4696
Digital Key Telephone System660.3
TOLL RESTRICTION PROGRAMMING
A.Entering Toll Table ProgrammingProgramming Steps
If the system is in the programming mode, continue
using the program codes. If starting to program here,enter the programming mode. Refer to Sec. 600.2,
Program Mode Entry (Key Station).
It is recommended that the Exception Tables be
initialized prior to entering data into the tables.
;.Dothis by following the
instructionsin Sec....

STARPLUS @ SPD 4696
Digital Key Telephone SystemEXCEPTION TABLES PROGRAMMING
EXCEPTION TABLES PROGRAMMING (Cont’d)
B.Allow Table ProgrammingProgramming Steps
1.Press the ALLOW TABLE A or ALLOW TA-
BLE B flexible button (Button 
#1 or #3). The
following message is shown on the display
telephone:
The first two bins locations are displayed.
2.Enter the two-digit bin number (01-20) of the
bin to be programmed.
It is recommended that: Bin 
f7 be reserved for
an entry mat will reference special table number
1;...

EXCEPTiON TABLES PROGRAMMING
STARPLUS @ SPD 4696
Digital Key Telephone System
EXCEPTlON TABLES PROGRAMMING (Cont’d)
Allow Table Programming (Cont’d)
Programming Steps
- {S)= Search Special Table Command
(TRANS button)
2. For an entry that is to reference the Home
Area Code table (special table 4) the entry
may also be entered to expect or not expect
a leading digit [l]. In fact in some cases it maybe desirable to enter both of the following
entries;
Leading digit [I]: enter 
BB 1 DDD {S} and/or
Non...

STARPLUS @ si=D 4896
Digital Key Telephone SystemEXCEPTION TABLES PROGRAMMING
EXCEPTION TABLES PROGRAMMING (Cont’d)
C.Deny Table ProgrammingProgramming Steps
1.Press the DENY TABLE A or DENY TABLE
B flexible button (Button 
#2 or #4). The follow-
ing message is shown on the display phone:
The first two bin locations are displayed.
2.Enter the two-digit bin number (01-I 0) of the
bin to be programmed.
3.Enter the deny code:
where:
- 0 to 9, l ,# = corresponding deny digits
(numbers)
- MUTE = Don’t Care...

EXCEPTlON TABLES PROGRAMMING
STARPLUS @ St’D 4696
Digital Key Telephone SystemEXCEPTION TABLES PROGRAMMING (Cont’d)
D. Speciai Table Programming
Programming Steps
To program a special table, it is first necessary to
assign an area.code to the table (except for the homearea code).
To assign an area code to a special table:
1.Press the appropriate AREA CODE TABLE
(l-4) flexible button (button 
#9-l 1). The fol-
lowing message is shown on the display
phone:
2.Enter the three-digit area code.
3. Press the...

STARPLLJS @ SPD 4696
Digital Key Telephone SystemEXCEPTION TABLES PROGRAMMING
EXCEPllON TABLES PROGRAMMING (Cont’d)
E.Displaying Toll Table Entries
Programming Steps
To display entries in either the Allow/Deny tables or
the special tables:
1.Press the DISPLAY TABLES flexible button
(button 
#12) while entering information into a
table.
2.While viewing entries made into an allow or
deny table, two entries at a time will be dis-
played on the bottom line of the display. By
pressing the DISPLAY TABLES...

WJS @ SPD 4696
d Key Telephone System
:ON 666
665.1665.2TABLE OF CONTENTS FOR SECTION 665
LEAST COST ROUTING (LCR) PROGRAMMING
...............................665-l
INTRODUCTION
............................................................................................665-l
A.LCR Operation...............................................................................665-l
LCR TABLES PROGRAMMING
...................................:.................................665-4
A.3-Digit Area/Office Code...

STARPLUS ’ SPD 4696
Digital Key Telephone SystemLEAST COST ROUTING 
&CR) PROGRAMMING
SECTION 665
LEAST COST 
ROUTlNG (LCR) PROGRAMMING
665.1INTRODUCTION
This feature is available with optional 
software.
Least Cost Routing (LCR) selects the most economi-cal programmed route for an outgoing call. When a
station user dials an outside number, the LCR fea-
ture analyzes the number and then automatically
chooses an outside line from the group that has beenprogrammed as most economical. The LCR feature
puts...

LEAST COST ROUTING (LCR) PROGRAMMINGSTARPLUS @ SPD 4696
Digital Key Telephone SystemRoutes are determined by the time of day and day
of week as specified in the Daily Start Time table andthe Weekly Schedule table.
After the appropriate route is selected, LCR Class of
Service becomes applicable. A station can use only
those line groups programmed with a priority number
equal to or higher than the station’s LCR Class of
Service.
If a line is not available in the first choice line group,
the system advances...

STARPLUS * SPD 4696
Digital Key Telephone SystemLEAST COST ROUTING (LCR) PROGRAMMING
SEARCH EXCEPTION
TABLE FOR MATCHj  FOUND ’ROUTE ASSIGNED !FROM EXCEPTIONITABLE- 1.
-.-I
TI
COMPARE 
# DIALED IWITH STATION’SiDIALING PRIVILEGES !
SYSTEM
CLOCK
YI  YES
j NOT I
SEARCH IFOUND&DIGITITABLE FOR
MATCH
7NOT’  LISTSELECTED FOR ’RESTRICTjROUTE FROM DAILYISTART TIME ANDI/  ‘NEEKLY SCHEDULE /YTABLES/!
6-DIGITTABLE !1
1  CO LINE SELECTED ;
I
FROM FIRSTIjAVAILABLETRUNK /GROUP IN LISTOF/
//I
ALL LINES/ROUTE ASSIGNED !...