Vodavi Starplus Spd 4896 Hybrid Key Telephone System Installation Manual

STARPLUS @ SPD 4896
Digital Key Telephone System1NlTlALlZE DATABASE PARAMETERS
INIT. DATABASE PARAMETERS (Cont’d)N. System Reset
Programming Steps
If the system needs to be reset but not initialized:
1.Press the RESETflexible button (Button #20).The following message will be shown on the
display phone:Description
This feature provides a hard system reset from thekeyset instead of the KSU. This is useful in cases
where miscellaneous data errors have occurred and
the system needs to be reset without...

STARPLUS @ Sf’D 4896
Digital Key Telephone System
TABLE OF CONTENTS FOR SECTION 675
SECTION 675PRINTING SYSTEM DATABASE PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .675-l
675.1INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .675-l
A.
B.
C.
D.
E.
F.
G.
Ii.
I.
J.
K.
L.
M.
N.PrintingSystemParameters...

STARPLUS @ SPD 4696
Digital Key Telephone SystemPRINTING SYSTEM DATABASE PARAMETERS
SECTION 675
PRINTING SYSTEM DATABASE PARAMETERS
675.1INTRODUCTION
Programming Steps
If the system is in the programming mode, continue
using the program codes. If starting to program here,
enter the programming mode. Refer to Sec. 600.2,
Program Mode Entry (Key Station).
If 
DataBase Parameters need to be printed:
1.Press FLASH and dial [85]. The following willDescription
This section describes the procedures and steps...

‘RINTING SYSTEM DATABASE PARAMETERS
STARPLUS @ SPD 4696
Digital Key Telephone System
iystem 
DataBase Printouts (Cont’d)
4. Printing System Parameters
Programminq Steps
f a printout of all System Parameters is desired:
1. Press the SYSTEM PARAMETERS flexible
button (Button 
#l). The following message
will be shown on the display phone:
2. To print the system parameter database ,
press the HOLD button. The following mes-
sage will be shown on the display phone:
RJhen the system has finished sending the...

STARPLUS @ SPD 4896
Digital Key Telephone System
PRINTING SYSTEM DATABASE PARAMETERSSYSTEM PARAMETERS
Eng. 
Ver.2.3D-OFFFSYSTZM TPIEISaSHR EHR ART XFR 
PFT CFN PT
60 180
145
1015 2
CDT CFT 
_ _DmO COT SRT ?lWT HCT18010 15 3 20
0 10
HFD CQT AC3 RR RG10 30
0 0 3
SYSTZM ZATURES
A0 SY 9NR EO PW BGM LCR
N
YX YYYNAC GL S CC 
MH V QN NY N YSN
3ARG2IN WARN TON?ZNAiJL,?3
SYSTEMLZD SLASH RATZS
INC CO FNG30 I?M FLAS%INCICM RISG120 13M SLiJTT7RCALLTORWA??30 11M FLASH-XESSAGE WAZING15IPM TLASH
AT3TxIqT STATIONS
100...

PRINTING SYSTEM DATABASE PARAMETERSSTARPLUS @ SPD 4696
Digital Key Telephone SystemSystem 
DataBase Printouts (Cont’d)
B.Printing CO Line Attributes
Programming Steps
If a printout of the CO Line Attributes is desired:
1. Press the CO 
LINE ATTRIBUTES flexible
button (Button 
#2). The following message
will be shown on the display phone:
To print the data for ALL CO Lines, press the
HOLD button. To print CO Line data for a
specified CO Line Range enter four digits to
specify the CO Line range (two digits...

STARPLUS@ SPD4996Digital Key Telephone SystemPRINTING SYSTEM DATABASE PARAMETERS
r
co 05
--
LiNE 05
CO LINE ATTRIBUTES
co 01
LINE 01SIGNAL TYPE UNA CONF PRI
DTMF CO YY YSIGNAL TYPE C?A CONF PRIDTMF co Y
Y Y
SrjPV DISA FLTM GRP COS DIR RDx\T13 1 12JOSi;SV 3iSA lLTM GRP COS DiR 3D
NN1011200RING ASSZG1WZNTS
100s
RING ASSIGNMENTS
1009co 06
--
LINE 06co 02
--
LINE 02SIGNAL TYPE UNA CONF DRIDTMF CO YY YSIGNAL TYPE LTNA CONF PRI
DTPP co Y _ -v vSUPV 3ISA FLTX GRP COS DIR RD
N N 1011200
COS DIR RD12003iNG...

PRINTING SYSTEM DATABASE PARAMFTERS
STARPLUS @ SPD 4696
Digital Key Telephone System
System 
DataBase Printouts (Cont’d)
C. Printing Station Attributes
Programming Steps
If a printout of the Station Attributes is desired:
1. Press the STATION ATTRIBUTES flexible
button (Button 
#3). The following message
will be shown on the display phone:
PRESS HOLD
2.To print data for all stations, press the HOLD
button. To print Station data for a specified
Station Range enter six digits to specify the
Station range...

STARPLUS @ SPD 4696
Digital Key Telephone SystemPRINTING SYSTEM DATABASE PARAMETERS
STATION ATTRIXJTES
STA 100
PAGE DND CONF ZOR PRI SPD QUEY Y YN/A Y Y Y
ILA OHVO FWD 3CR SUE REXNN Y N NNSI3 AID 3cos sicos SPK
0_(i03ICXUO PAG; IRETWD LCOS
110CO ACCESS 1
3UTmONS
O&O0 02DlOl 03D10204D103 05Di04 06D105
07D106 08D107 09D10810D109 llDl10 12Dlll
13coo1 l4COO2 15coo3LSCOO4 L7C005 18cOO6
19L12OPL1 21C3K22FwD23DND2acwSTA 
101
STA 102
PAGE DND CONF EOR PRI SPD 
QUEY Y YN/A Y Y YPLA OHVO Fwl LCR SUE REM
NN Y N N...

PRINTING SYSTEM DATABASE PARAMETERSSTARPLUS @ SPD 4896
Digital Key Telephone SystemSystem 
DataBase Parameters (Cont’d)
D.Printing CO and Station Port Parameters
Programming Steps
If CO/Station parameters need to be printed:
1. Press the CO/Station Port Parameters 
fiex-ible button (Button 
#4). The following mes-
sage will be shown on the display phone:
yiiG&Ep
PRESSHOLD2. To print the CO/Station Port parameters,
press the HOLD button. The following mes-
sage will be shown on the display phone:
+When...