Vodavi Starplus Spd 4896 Hybrid Key Telephone System Installation Manual

STATlON ATTRIBUTES PROGRAMMING
STARPLUS @ SPD 4696
Digital Key Telephone SystemPAGE 
“6” STATION ATIRIBUTES (Cont’d)
K. Display Flexible Buttons
Programming Steps
If the flexible buttons are to be viewed:
1.Press the DISPLAY BUTTONS flexible button(Page B, Button 
#17). The programming as-
signment on four buttons will be displayed
starting with the lowest button number. With
each sub-sequent depression of the DIS-
PLAY BUTTONS button, the next four buttonswill be displayed. The following message is...

STARPLUS @ SPD 4896
Digital Key Telephone SystemSTATlON AlTRIBUTES PROGRAMMING
PAGE 
“B” STATION AmTRIBUTES (Cont’d)
630.3
DIGlTAL DATA INTERFACE UNIT
(DDIU)
Programming Steps
To program a Digital Data interface (DDIU) unit:
a. Press FLASH and dial 
[51]. The following mes-
sage is shown on the display phone:
Where:
- WWW = Station Number (100-l 95)
- XXXXX= Baud Rate
- Y= Data Parity
- Z= Data Stop Bits
b. Enter the three-digit station number of the DDIU
unit.c. Press the HOLD button to save the entry....

STARPLUS @ SPD 4896
STATlON ATRIBUTES PROGRAMMINGDigital Key Telephone SystemDigital Data Interface Unit (DDIU) (Cont’d)
B. Character Length Option
Programming Steps
1. Press the CHARACTER LENGTH flexible
button (Button 
#2).2. Enter a one-digit number for the character
length of the digit string.
- [8] = 8 character length
- [9] = 9 character length
3. Press the HOLD button to save the entry.
Confirmation tone is heard and the display willnow update.
C. Stop Bit(s) Option
Programming Steps
1.Press the...

STARPLUS @ SPD 4696Digital Key Telephone System
STATlON AlTRIBUTES PROGRAMMING
PAGE “B” STATION 
AlTRIBUTES (Cont’d)
630.4
FLEXIBLE PORT ASSIGNMENT FEA-
TURE
Programming Steps
If the Station numbers need to be relocated to differ-
ent ports:
a. Press FLASH and dial 
[52]. The following mes-
sage is shown on the display phone:
b. The buttons 1 through 8 indicate cards 1
through 8. When the relocation program is in-
itially entered, Button #1 will be lit indicating thatthe user is programming the Station...

STARPLUS @ SPD 4696
Digital Key Telephone SystemSECTION 640
640.1640.2
640.3TABLE OF CONTENTS FOR 
SECTiON 640
ICLID PROGRAMMING.............................................................................640-l
INTRODUCTION
............................................................................................640-I
A.CallingNumber/NameDisplay.......................................................640-I
6.Incoming Number/Name for SMDR...............................................640-l
C.Unanswered...

STARPLUS @ SPD 4696
Digital Key Telephone SystemICLID PROGRAMMING
SECTION 640
ICLID PROGRAMMING
640.1INTRODUCTION
This feature is available with optional software.
The 
ICLID (Incoming Calling Line IDentification) fea-
ture has been added to the 
Starplus Digital Key
Telephone System. However, these features are not
available unless the Basic ICLID Software package
has been purchased separately. The operation of
this feature is dependent on the feature first being
activated from the central office so...

ICLlD PROGRAMMING
STARPLUS * SPD 4696
Digital Key Telephone SystemICLID PROGRAMMING (Cont’d)
640.2
ICLID RINGING ASSIGNMENT
Programming Steps
If the system is in the programming mode, continue
using the program codes. If starting to program here,enter the programming mode. Refer to 600.2,
Program Mode Entry (Key Station).
If ICLID Ringing Assignments need to be assigned
or changed:
1. Press FLASH and dial 
[43]. The following
message is shown on the display phone:
Where:
2.
3.
4.
- 000= ICLID Route...

STARPLUS @ SPD 4896
Digital Key Telephone SystemICLID PROGRAMMING
ICLID PROGRAMMING (Cont’d)
ICLID Ringing Assignment(s) (Cont’d)Programming Steps
Ring assignments will be continuous and will be
displayed in order of the destination number from
001 to 557.
5.Repeat Step 3 to program additional stations
and ringing assignments. A maximum of eight
stations will display on the LCD display. Addi-
tional stations and ringing assignments can
be displayed using Button 
#17.To advance to the next Route:
1.Press...

ICLID PROGRAMMINGSTARPLUS @ SPD 4896
Digital Key Telephone SystemICLID PROGRAMMING (Cont’d)
640.3ICLID FEATURES
Programming Steps
If ICLID is to be used:
1. Press FLASH and dial 
[56]. The following
message is shown on the display phone:
2. To program ICLID features, use the flexible
button(s) as defined in the following proce-
dures. The ICLID, NAME buttons toggle on
and off.
3. After all entries are made, press the HOLD
button to accept the data.
A.Enable/DisableProgramming Steps
1.Press the ICLID...

STARPLUS @ SPD 4896
Digital Key Telephone SystemICLID PROGRAMMING
ICLID PROGRAMMING (Cont’d)
ICLID Features (Cont’d)
C.Programming Steps
Baud Rate Display
The ICLID Baud Rate is programmed using
Flash 15 Baud Rate Assignments. Button X3
will return error tone when pressed. The LCD
displays the current baud rate based on which
Port number is assigned to the ICLID Port num-
ber.D. Port Assignment
Programming Steps
1.Press the PORT flexible button (Button #4) to
determine which port is to be used for ICLID...