Trillium Panther Ii Feature Module Iv System Manual

Trillium Standard Practice 
3. OPTIONS INTERFACE HARDWARE UNIT 
GENERAL 
3.01 When used with Feature Module II software, the Options Interface Hardware 
Unit enhances the operation of Panther II systems by providing the following 
new features: 
l Amplified Lines, 
l Trunk to Trunk Conference, 
l External Call Forward, and 
l Direct Inward System Access. 
Note that you can only use the Options Interface Hardware Unit if your system has 
Feature Module II software. In addition the Options Interface...

Panther II 820/1032/2064-296 
14.75” (37.46 cm) 275” 
5% Crr 
1 = 7.7 (19.6 cm) 4 1.5” 
(3.76 cm) 
Figure 3-l Mounting the Options Interface Hardware Unit 
Step 7. Plug one end of the supplied ribbon cable into the port that you uncovered in 
Step 6. Refer to Figure 3-3 to locate the correct port on the KSU. The connec- 
tor fits into the port only one way. Don’t attempt to force the connector into the 
port. 
Step 8. Plug the other end of the ribbon cable into the port on the left panel of the 
Options...

Trillium Standard Practice 
0 1 
Key Service 
Unit 
 
0 2 
0 3 
Figure 3-2 Exposing the Port for the Ribbon Cable 
Feature ModLIe II & Options Interface Hardware 
Page 14  

Panther II 820/1032/2064-296 
Figure 3-3 Connecting the Ribbon Cable 
Key Service Unit 
Figure 3-4 Installation Complete 
Feature Module II & Options Interface Hardware 
Page 15  

Trillium Standard Practice 
FEATURES 
3.03 This section provides descriptions and programming instructions for the features 
made available by the Options Interface Hardware Unit. 
Amplified Lines 
Normally, during an external conference there is a slight reduction in the voice signals 
over the C.O. lines. To remedy this inconvenience, the Options Interface Hardware Unit 
has a built-in amplifier that compensates for reductions in the voice signals on external 
conference calls. 
External conference...

Panther II 820/1032/2064-296 
Step 4. 
Dial the data code of your selection: 
Length of Time 
Data Code 
0 m@es (No 
Trunk ‘9 Trunk Conferencing) 
0 
: IIIXIIE; (default semng) 
; 
10 minutes 
3 
Step 5. Dial # to store your selection. The Intercom indicator lamp comes on steady. 
Step 6 Dial * to exit programming mode. 
Operation 
You must establish an external conference call on amplified lines before you can set up 
a Trunk to Trunk Conference: 
While on an external call, 
l Press the Hold key 
The...

Trillium Standard Practice 
With the handset in the cradle, 
l Dial *, press the line key of one of external lines being used for the 
conference 
or 
Dial *0, dial the line number (01-20) of one of the external lines being 
used for the conference 
Two tones announce your entry into the call in progress. 
l Lift the handset. 
Operating Notes 
If you exit and then re’enter a Trunk to Trunk Conference, the timer for the Trunk to 
Trunk Conference will be restarted when you hang up. 
Direct Inward System...

Panther II 820/1032/2064-296 
You can program each of the incoming DISA lines separately for Day or Night Mode 
operation. Each of the lines can have one of four possible settings: 
l Day off/Night off - DISA won’t work during the Day or Night Mode (default setting), 
l Day on/Night off - DISA will work only during Day Mode, 
l Day off/Night on - DISA will work only during Night Mode, or 
l Day on/Night on - DISA will work during both Day and Night Mode. 
You can also change the default setting of the...

Trillium Standard Practice 
Step 6. Program the Day/Night Mode selection for incoming DISA line 2 (only if you 
programmed an incoming DISA line 2 in Step 3). 
a. Dial access code 0381. 
b. Dial data code 0 for Day off/Night off (default setting), 
1 for Day on/Night off, 
2 for Day off/Night on, or 
3 for Day on/Night on, 
c. Dial # to store your selection. 
Step 7. Enter the desired release time. Note that the length of time selected will also 
determine the release time for ECF. To program the DIWECF...

Panther II 820/1032/2064-296 
l Dial the desired telephone number 
After several seconds of silence you will hear ringing. When the person answers, 
begin your conversation. If the parry doesn’t answer dial O# and hang up the handset. 
Both you and the person you’re speaking with will hear an I1 -second warning tone 
before the preprogrammed release time expires. If you wish to continue your conver- 
sation, either you or the person you’re calling can dial * during the tone to restart the 
timer. Note...