Trillium Panther Ii Feature Module Iv System Manual

Trillium Standard Practice 
0 Status 
Call arrive 
I 
Hold Recall 
! 
Busy 
Override 
3 
Back Tone 
Tone Signal Tone Frequency 
Synchronizes with incoming ringing signal. a: 430 Hz 
1132s 
lt32s b: 580 Hz 
:::::::::.  :;:s:g 
:, :.:.:: ,.,:,: ::: -:::::.:::i’:._-  .:i,:.:_.: :.:.:.: :.:.:::.:p~:.~ :. 
x.:+>:.:.:.:.:.:.:.:+: :,:, ,,.,. i :.:,:  . . .  I;~:j:::~::::::::::~:::~: :.:,:,., :.:. 
: .:.: .‘. .‘.‘.‘. ::.:.: .“::.A:  ..:.::.:: j:::: s:: ..:. : . . . . 
:::x:;:;:  :j::::::,; .430 Hz modulated 16...

Panther II 820/1032/2064-105 
4. SYSTEM FEATURES 
AUTO HOLD 
Description 
This feature allows you to place an external call on hold simply by pressing 
a DSS key and then transfer the call by announcing to the person at the 
station to pick up the line that the call is on. This capability is assigned on a 
set-by-set basis. If Auto Hold is not programmed, you will have One 
Touch Speed Dial capability, where speed dialing is available by pressing a 
DSS key. 
Conditions 
l Auto Hold is programmable for...

Trillium Standard Practice 
Programming Required 
l Access Code 113 - Manual Select / Auto Intercom / Auto Line Select. 
BATTERY BACKUP CAPABILITY 
Description 
Each Panther II Key Service Unit has an interface for an external 24 Volt dc 
battery backup unit (optional) inrder to maintain full system operation 
during an electrical power failure. With a 24 Vdc battery backup unit 
connected, when the power fails, the system will automatically switch over 
to battery operation for the duration of the power...

Panther II 820/1032/2064-105 
When a caller is camped-on, the busy station will hear a single l-second 
beep through their Set’s speaker, at preprogrammed intervals (Camp-On 
Tone Interval) to alert them that a call is waiting. After a preprogrammed 
length of time (Camp-On Duration), ringing returns either to the originator 
or to the attendant (or sub-attendant), depending on Transfer Ringing 
Return programming. The originator of the Camp-On also has the 
capability of retrieving the call at any point...

Trillium Standard Practice 
Cancel - terminates an external call and returns dial tone without hanging up 
the handset. This is the Panther II system’s preprogrammed choice and is 1 
second in duration. 
Tran.$er - transfers an outside call to another station. 
Conditions 
The duration of the Flash or Cancel signal must be properly set to 
ensure correct operation. 
If the Panther II system is placed behind PBXKentrex, the 
programming should be set to FLASH capability. 
Only one choice (Flash, Cancel or...

Panther II 820/1032/2064-105 
Conditions 
l If extensive programming is necessary, it is recommended that the Master 
station number be changed. 
Programming Required 
l Access Code 053 - Flexible Master Station Programming 
FLEXIBLE RINGING ASSIGNMENT 
Description 
Used to program ringing for each station. Except for Station 10, each 
station is preprogrammed NOT to ring during an incoming call on any line. 
Lines are programmed individually and may, or may not appear at a Set. 
Conditions 
None...

Trillium Standard Practice 
Conditions 
l Class A (the preprogrammed value), must be changed to Class c’ to 
restrict outgoing calls on a line. 
Programming Required 
l Access Code 065 - Toll Restriction by Line 
INTERCOM ON HOLD 
Description 
An 
intercom (internal) call can be placed on hold, and the calling party will 
hear music if it is wired to the system. Intercom on Hold is programmed 
during system programming and is a systemwide feature that allows an 
internal call to be placed on hold...

Panther II 820/1032/2064-105 
telephone Sets. There is one primary line pool with an unlimited number of 
lines, and three other pool groups with an unlimited number of lines per 
group. 
If a line pool key is not available, a code can be dialed to select the line pool. 
This allows Sets such as the Panther II Set (Basic Set) to access line pools. 
The codes for selecting line pools are as follows: 
Line Pool Code 
1 401 
; 403 402 
4 404 
When the line pool key is pressed, the system selects the first...

Trillium Standard Practice 
l Access Code 063 - Loud Bell 
Mode) 
l Access Code 064 - Loud Bell 
(Night Mode) Ringing/Ringing Over Paging by Line (Day 
Ringing/Ringing Over Paging by Line 
MULTIPLE ATTENDANTS 
Description 
A Master Attendant and up to three additional sub-attendants can be 
designated per Panther II system (in conjunction with the four possible 
Intercom Tenanting / Station Hunt Groups). The Master Attendant is 
preprogrammed as Station 10 but may be changed through “Flexible Master...

Panther II 820/1032/2064-105 
NIGHT TRANSFER GROUPS 
Description 
In 
Night Transfer, all of the lines are put into one of four “Night Transfer 
Line Groups”, and then each of the stations are put into one of the four 
“Night Transfer Station Groups”. 
This flexible programming tells the 
system which lines will ring at which stations when the system is operating 
in Night Mode; for example, Group 1 may be programmed to ring certain 
lines in Night Transfer mode, while Groups 2,3, and 4 are programmed to...