Trillium Panther Ii Feature Module Iv System Manual

Trillium Standard Practice 
Initial Installation 
(for previously installed systems, go to the next section) 
The following instructions detail initial installation of the Feature Module II 
Cartridge. 
CAUTION: Don’t plug in the KSU power cord until you are instructed to do so. 
Step 1. 
Step 2. 
Step 3. 
Step 4. 
Step 5. 
Step 6. 
Step 7. 
Step 8. Mount the KSU as per the instructions in the 
Installation and Commissioning 
Practice 
of the Panther II System Manual. 
There are two small grooves on the...

Panther II 820/1032/2064-296 
Replacing the Feature Module Cartridge 
The following instructions detail the replacement of a Feature Module Cartridge in an 
existing installation. 
Step 1. 
Step 2. 
Step 3. 
Step 4. 
Step 5. 
Step 6. 
Step 7. 
Step 8. 
Step 9. 
Step 10. 
Step 11. Set the MEM. CLEAR Switch to the ON position. The MEM. CLEAR Switch 
(dipswitch #2) is located on the right-hand side panel of the KSU. 
Press the RESET Switch. 
Set the MEM. CLEAR Switch to the OFF position. The system is now...

Trillium Standard Practice 
KSU 
Port for Feature 
Module II Cartridge 
FEATURE MODULE II CARTRIDGE 
it securely into the pot-~ on the KSU. 
Protective Casing 
Feature Module II 
Cartridge 
 
Flange for screws 
Plastic Expansion Plugs 
Figure 2-I Installing the Feature Module II Cartridge 
Feature Module II & Options Interface Hardware 
Page 4  

Panther II 820/1032/2064-296 
ADDITIONAL FEATURES 
2.03 This section provides descriptions and programming instructions for the addi- 
tional features that are available with Feature Module II software. 
Additional Programmable Feature Keys 
Panther II systems allow you to program feature codes into the line keys and Direct 
Station Select (DSS) keys that are located on the set’s designation card (i.e., the line/DSS 
keys that are located above the fixed function keys). Once you’ve programmed a line/...

Trillium Standard Practice . J 
.:.i _:’ 
, 
Programming 
Feature keys are programmed at each individual set. To program a line/DSS key to 
activate a feature: 
Step 1. Dial *# (or press the 
Program key) at the set. 
Step 
2. Dial the digit 4. 
Step 3. Press the line/DSS key that you wish to program. Remember, you can only 
program line/DSS keys that are located on the set’s designation card. 
Step 4. 
Dial the code of the desired feature (e.g., dial 
063 to program the key to 
activate background...

Panther II 820/1032/2064-296 
Transfer Ringing Return Displays 
Feature Module II software provides displays for the Transfer Ringing Return feature. 
When an incoming external call is transferred to another station, if the call isn’t answered 
within a programmable time period the call will either: 
l return to the station that transferred the call, then be sent to the Master Attendant 
Station (or sub-attendant, if sub-attendants are programmed), 
l be sent directly to the Master Attendant Station (or...

Trillium Standard Practice 
If a name has been programmed for the station that the call is being recalled from, the 
name instead of the station number will appear in the liquid crystal display. 
Example: 
Recalled from Tony 
Line 3 
Operating Notes 
Assume your station is programmed to have unanswered, transferred calls returned to 
your set, then returned to the Master Attendant Station. If you transfer two incoming 
external calls to different stations and neither of the transferred calls are...

Panther II 820/1032/2064-296 
Step 3. Dial 015. The Intercom indicator lamp turns on and the display confirms that 
you are in programming mpde. 
Step 4. Dial 028. The Intercom indicator lamp flashes quickly. 
Step 5. Enter the desired 4-digit 
RPASS access code. 
Step 
6. Dial # to store the code. The Intercom indicator lamp comes on steady. 
Step 7. Dial * to exit programming mode. 
Using RPASS to Program a Customer’s System 
Once a 4-digit RPASS access code has been programmed, you can use RPASS to...

Trillium Standard Practice 
_.. --1 
:, 
Step 5. Dial the 3- to 7-digit access code of the feature you wish to change, then dial #. _ / 
(The feature access codes are given in the Programming Prucrice). Each digit 
will be displayed in your set’s liquid crystal display as you dial it. The setting 
currently programmed for the feature will be displayed. 
Access code 000 for Hold Recall Time 
Current setting for Hold Recall Time 
Data Code = 2 so Hold Recall Time is 
Programmed for 1 minute. 
Step 6. To...

Panther II 820/1032/2064-296 
Step 8. To confirm your programming selections enter the first access code by dialing 
OOO##. Press # to step through each access code.. The data code currently pro- 
grammed for each access code will be displayed. 
Press # to step to the next feature. 
The access code and data code 
programmed for the system are 
displayed. 
Step 9. Press the * key to exit programming and release the line. Programming is com- 
plete. 
Step 10. Hang up’the handset or, if handsfree, press the...