Trillium Panther Ii Feature Module Iv System Manual

Mite1 Standard Practise 
Station Display 
When you place a internal call from a Panther II Display set, the station that you’re 
calling is indicated in the liquid crystal display. With Feature Module I or Feature 
Module II software, the station is indicated by “Ext. XX”, where XX is the station 
number. With Feature Module IV software, the display has been changed to “Stn 
xx”. 
EXAMPLE: 
FM 
I or FM II Software Display FM IV Software Display 
Display for Transfer Ringing to Attendant Station 
When a...

Panther II 820/1032/2064-297 
3. ON PREMISE STATION UNIT 
General 
3.01 The On Premise Station (ONS) Unit provides a 4-port interface between Panther 
II 820/1032/2064 Systems and the following devices: 
l single-line set 
l auto attendant 
l voice mail system 
The ONS unit is a sealed unit of metal construction measuring 34.0 cm (13.4 inches) high, 
23.9 cm (9.4 inches) wide and 6.54 cm (2.6 inches) deep. 
Feature Module IV & On Premise Station Unit 
Page 7  

Mite1 Standard Practise 
9.4” (23.9 cm) 
8.2” (20.8 cm) 
I 
I 
*I 
2.6” (6.54 cm) TOP 
LEFT-SIDE ) Modular 
Jack for 
Connecting 
the 
Station 
Ports 9.4” (23.9 cm) 
FRONT 
BOTTOM 
2.6” (6.54 cm) 
Modular 
Jack for 
Connecting the 
devices 
Dip Switch for 
Programming 
the 
Hookswitch 
Recognition 
Time 
RIGHT-SIDE 
Figure 3-1: On Premise Station Unit 
Feature Module IV & On Premise Station Unit 
Page 8  

Panther II 820/1032/2064-297 
Performance Requirements 
The ONS 
Unit has the following performance requirements: 
ENVIRONMENTAL 
Storage Temperature 
-20 to +6O”C 
Functional Temperature 
+5 to +40°c 
Recommerided Operating Temperature 
+15 to +35”C 
Humidity 
0 to 90% non-condensing 
Table 3-1: Environmental Requirements 
POWER 
AC Power 115 Vat k 10% (50/60 Hz) 
0.5 Amu max load 
Battery Backup Power 
1 24Vdc 
Table 3-2: Power Requirements 
Feature Module IV & On Premise Station Unit 
Page 9  

1 
Mite1 Standard Practise 
# 
A 
B 
C 
D 941 
697 
770 
852 
941 
Table 3-3: DTMF Signaling Frequencies 
1477 
1633 
1633 
1633 
1633 
DTMF DIGIT 
TRANSMISSION TIMING 
Manual Access True DTMF 
Automatic Access Tone Duration 
over 100 ms 
(programmable) 
over 200 ms 
over 300 ms 
over 400 ms 
Interdigit Pause 
over 100 ms 
(not programmable) 
Table 3-4: DTMF Digit Transmission Timing 
Feature Module IV & On Premise Station Unit 
Page 10  

Panther II 820/1032/2064-297 
DETECTION TIMING 
DTMF Digit Duration 
Interdigit Pause Duration 
I 40 ms minimum 
I 40 ms minimum 
Table 3-5: Detection Timing 
RINGING GENERATION 
Ringing Voitage 200 V p to p (square wave) 
Ringing Frequency 
209~ 5Hz 
Incoming C.O. line call, 
Incoming DISA line call, 
Transfer Ringing call, 
and Hold Recall 
Incoming Intercom call 0.5 seconds ringing 
0.25 seconds pause, 
0.5 seconds ringing, and 
3.75 seconds off 
1.0 second ringing and 
4 seconds off 
Table 3-6:...

Mite1 Standard Practise 
Tone Generation from Panther Sets 
The ONS 
Unit generates DTMF tones to enable Panther set users to access a voice mail- 
box or signal an auto attendant. Table 3-7 shows the digits that must be dialed on a 
Panther set to generate the different dialing tones required by a voice mail system or auto 
attendant. An ONS Station must be programmed for an auto attendant or a voice mail 
system, before the ONS Unit will generate DTMF tones for that ONS port. 
-. A 
i 
I 
lXGlTS DTMF...

Panther II 820/1032/2064-297 
Direct Inward System Access 
The ONS 
Unit is designed to operate with the DISA feature. If your system has an Op- 
tions Interface Unit and is programmed for Direct Inward System Access, then you can 
call into the Panther II system and place internal calls directly to ONS stations. 
Call Progress Tones 
The ONS 
Unit provides the following call progress tones: 
AUDIBLE RINGS: 
- CO. line ringing tone 
- btemal DISA ringing tone 
- Transfer ringing tone 
- Hold Recall...

Mite1 Standard Practise 
Installation 
3.02 The On Premise Station (ONS) Unit connects to station ports on the left-hand side 
of Panther II 820,1032 and 2064 KSUs. The ONS Unit supports up to four devices and 
each device occupies a station port on the KSU. In order for the ONS unit to operate, 
Feature Module IV software must be installed in the KSU. 
You can connect a maximum of two ONS Units to a Panther II 820,1032 or 2064 Sys- 
tem. However, you can’t connect an ONS Unit to more than one KSU. For...

Panther II 820/1032/2064-297 
c. 
Dial access code 1OOYY where YY is the 2-digit station number of the ONS 
device 
d. 
Enter the desired data code: 
5 for a single line set, 
6 for a voice mail system, or 
7 for an auto attendant 
e. 
Press the # key to store your selection 
f. 
Repeat steps c to e for each ONS station 
g. 
Press * to exit programming mode 
KSU 
KRONE BLOCK 
ODULAR CONNECTOR 
STANDARD SET 
Figure 3-2: On Premise Unit Installation 
Feature Module Iv & On Premise Station Unit 
Page 15