Toshiba Voice Processing Vp100, 300s, 300 Configuration Manual

VAR Specifies a variable length field. If no terminating digit is defmed, 
the field length varies according to the FIRSTDIGIT Table. 
A variable with a terminating DTh4F digit is valid for, all 
fie!d types. 
A variable without a terminating DTMF digit is valid only for source 
or destination field types 
Terminaff ng DTMF 
Dign Specifies the terminating digit for a variable length field. The digit 
can be 
a value from O-9, A-D, l , or #. 
I!3 The terminating digit cannot occur in a normal field. 
n...

10.2 HOW TO CONFIGURE THE DTMFINT TABLE 
The DTMFINT Table can be configured in two ways: 
l Modify System Parameter 3 - PBX TYPE and accept the default DTMFINT Table. 
l Use the UPDATE commands ADD and DELETE. I’- 
After configuring the DTMFINI’ Table, a listing of the configuration may be obtained via the LIST 
command in UPDATE 
IL.r IWalling a new system automatically configures the defaults. 
n Modifying System Parameter 3 
Use the MODIFY command to establish default values for the DTMFTNT 
Table...

10-6 Configuration Manual 
n 
Using the UPDATE Commands 
?he following UPDATE commands are applicable to the DTMFINT Table: 
l ADD 
l LIST 
I-- 
* DELETE 
ADD Adding call record formats to the DTMFINT Table 
A new caIl record format can be added in an existing DThEINT 
Table, or added to an already configured table after the obsolete 
information is deleted. A sample dialog follows, 
LIST 
DELETE Listing values configured In the DTMFINT Table 
Deleting the configuration Information for an entire call...

DTtJFlNT Tabie 10-7 
10.3 ERROR CHECKING DURING CONFIGURATION 
Three specific errors are checked during configuration: 
c Normal syntax and range 
0 First element 
c T@ield Validation 
l ‘- 
Normal Syntax and Entries are checked to verify that they conform to the established 
Range configuration syntax and range. 
flrst Element Verifies that the firs element is unique. If the first element is not 
unique, an error is generated and the 
DTMFINT Table must be 
corrected before continuing. For example:...

11 _ 
FIRSTDIGIT TABLE 
.‘- 
Chapter Contents 
PZ+Qe  Sect Q escrbtlon 
I n D 
11.1 lJn&stmding the FIRSTDIGIT Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 
11.2 How the FlRSTDlGlT Table is Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...11-2 
11.3 HOW to Configure the FIRSTDIGIT Table . . . . . 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

INTRODUCTION 
The FIRSTDIGIT Table defmes the first digit and length of valid mailbox numbers. 
The FIRSTDIGIT Table is generated from information entered into the USER Table, When a 
mailbox number is entered, the Toshiba VP System checks to see if there are other mailbox 
numbers beginning with the same first digit. If so, the number of digits for the newly entered 
mailbox must be the same as the previously entered mailboxes. For example, if all mailbox 
numbers heginning with ‘2” are three digits...

Quick Reference Guide 
FIRSTDIGIT Table 
Command Description 
FIRSTDIGIT 
Table Contains the mailbox length for each first digit defined 
in the USER Table. Also contains the initial digit length 
for network numbers. 
FIRSTDIGIT Table and the 
INSTALL Program There are no questions in the INSTALL program 
pertaining to fvst digits. Mailbox length is automatically 
assigned when mailboxes are entered into the USER 
Table. Network digits are automatically assigned when 
entering data into the NETWORK...

FIFISlDIGiTTabbe 11-1 
11.1 
UNDERSTANDING THE FIRSTDIGIT TABLE 
The FIRSTDIGIT Table contains the mailbox length for each firs digit defined in the USER 
Table. The table also contains the initial digit length for netwbrk numbers. Refer to the F&mm 
Dcuriptinmti - NETWORKING for additional information. 
m Single Digit Menu first digits are not subject to the constraints of the F&TDIGm Table. 
Example of a FIRSTDIGIT Table: 
~27 All first digits without values defined for Mailbox Length or Initial-Digits...

11-2 Configuration Maid - 
11.2 HOW THE FIRSTDIGIT TABLE IS USED 
The Toshiba VP System and many PBXs use FIRSTDIGIT Tables to determine: 
l Whether the firs digit is valid, and . 
l How many digits to expect before completing a call. +“ 
The fmt digit entry in the FIRSI?)IGIT Table is defined when the first mailbox starting with a 
given digit is entered in the USER Table. Vtid mailbox first diit numbers are 1 - 9. A ma&ox 
number cannot begin with the digit 0, however, extensions in the USER Table can...