Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

FEATURE USE FEATURE USE 
DO NOT DISTURB (continued) AUTOMATIC CALLBACK (INTERCOM) (continued) 
TO RELEASE THE DO NOT DISTURB MODE 
Press the m button. 
l DND LED goes off. 
NOTES: 
1. Do Not Disturb prevents Off-hook Call Announce. 
2. Outside calls will mute ring your station while in the 
DND mode. 
AUTOMATIC CALLBACK (INTERCOM) 
After reaching a busy or DND station on an intercom call, you 
may use Automatic Callback. 
TO USE AUTOMATIC CALLBACK 
1) Press them button (or dial 0) to set Automatic...

FEATURE USE 
FEATURE USE 
ACCOUNT CODE CALLS (continued) 
ACCOUNT CODE CALLS (continued) 
wish to record an account code voluntarily after either dialing an 
outside number or receiving an incoming call. The code you enter 
will be recorded on the Station Message Detail Recording 
(SMDR) printout with the details of your call. With Release3 only, 
account codes may be verified or nonverified. 
TO RECORD A FORCED ACCOUNT CODE (Outgoing Calls 
Only) 
1) Access a CO line.’ 
l You hear dial tone.2 
2) Dial...

FEATURE USE FEATURE USE 
ACCOUNT CODE CALLS (continued) 
2) Dial the three-digit verified account code number tI Cl It 
(000 - 299). 
3) Dial the verified account code O...Ct (4 * 15 digits). 
4) Press the 1 or m button to store the code. 
l You will hear confirmation tone. 
5) Repeat steps 1 w 4 to enter more verified account codes. DOOR PHONE 
NOTE: 
For security reasons, the account code change access 
code is not given in this guide. Contact your telephone 
system maintenance provider for this access...

FEATURE USE FEATURE USE 
HANDSFREE MONITORING BACKGROUND MUSIC OVER EXTERNAL SPEAKERS 
Calls placed on hold by the distant party may be monitored 
handsfree. 
TO USE HANDSFREE MONITORING 
1) While connected to a call, press and hold them button. 
2) Place the handset on-hook. 
3) Release the m button. 
l Sounds from the distant party are heard via the 
telephone’s speaker. 
4) Lift the handset to continue the conversation when the 
distant party returns. 
ALARM RESET 
A programmable option used with an...

FEATURE USE FEATURE USE 
DIRECT INWARD SYSTEM ACCESS (DISA) (continued) 
4B) If a DISA security code is not required, listen for CO dial 
tone. 
5) After receiving CO dial tone, dial the desired telephone 
number. 
6) A timer tone will sound6 approximately four minutes after 
the time the call was made. Dial 1 to reset the timer’ each 
time the tone sounds (this allows an additional four minutes 
of conversation). 
7) Hang up when the call is completed. 
NOTES: 
1. Dial tone will be present for 10...

FEATURE USE FEATURE USE 
MESSAGE WAITING MESSAGE WAITING (continued) 
If someone calls your telephone and you are unable to answer, 
the calling party may set the Message Waiting indicator (a 
flashing LED) on the called party’s telephone. 
The Message Waiting indicator is the MW/FL LED on the IO- or 
20-button electronic telephone. 
Up to four Message Waiting indications may be queued on the 
message indicator at one time. One of the four message indica- 
tions is always reserved for the Message Center;...

FEATURE USE FEATURE USE 
NIGHT TRANSFER 
PROGRAMMABLE OPTION OVERRIDE CALLS (continued) 
On an optional basis, your system can function with two or three 
ringing patterns. If three patterns are selected, they are desig- 
nated DAY, DAY 2, and NIGHT. If only two patterns are selected, 
DAY and NIGHT designations are used. 
In both cases, different ringing patterns are chosen by pressing 
the 
q button. Certain CO lines may be enabled in system pro- 
gramming to switch from normal operation to DISA line...

FEATUREUSE FEATURE USE 
SPEAKERPHONE (continued) 
MICROPHONE CONTROL (continued) 
TO MAKE AN INTERCOM CALL (On-hook Dialing) 
1) Leave the handset on-hook. 
2) Press the m button. 
l Listen for intercom dial tone. 
l INT LED flashes at the In-use rate. 
3) Dial the desired station number. 
l You hear a single ring tone. 
4) Speak at a normal voice level in the direction of the 
telephone. 
5) Press the m button when the call is completed to 
disconnect. 
MICROPHONE CONTROL 
The MIC button is used to...

FEATURE USE FEATURE USE 
TIMED REMINDERS (continued) 
TWO (TANDEM) CO LINE CONNECTION (continued) 
On some systems, the connection must be supervised and 
released as follows: 
1) Press either 
q button. 
l Both CO LEDs flash at the In-use rate. 
l You will be connected to both CO lines. 
2) If the parties have hung up, go back on-hook. 
l Both CO LEDs go off. 
l Connection is released. 
3) If the parties are still talking, proceed to step 5 above. 
NOTES: 
1. CO lines may be accessed bypressing am line...

FEATURE USE 
TOLL RESTRICTION OVERRIDE/TRAVELING CLASS 
(continued) 
l You will hear confirmation tone. 
4) Repeat steps 1 w 4 to enter more toll restriction override or 
traveling codes. 
NOTES: 
7. Traveling class is available with Release 3 only. 
2. For security reasons, the change access code is not 
provided in this guide. It is available from your tele- 
phone system maintenance provider. 
TONE SIGNALING 
PROGRAMMABLE OPTION 
Provides ringing on incoming intercom calls when voice an- 
nouncing is...