Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

FEATURE USE FEATURE USE 
OUTSIDE CALLS OUTSIDE CALLS (continued) 
TO MAKE AN OUTGOING CALL (DirectAccess) 
1) Lift the handset. 
2) Press any available 
q line button (or q button). 
l Listen for dial tone. 
l CO/PL LED flashes green at the In-use rate. 
3) Dial the desired telephone number. 
4) Hang up when the call is completed. 
TO MAKE AN OUTGOING CALL (Dial Access) 
1) Lift the handset. 
2) Press the m button. 
0 Listen for intercom tone. 
l INT LED flashes green at In-use rate. 
3) Dial CO line...

FEATURE USE FEATURE USE 
GROUP LISTENING REPEAT LAST NUMBER DIALED 
Allows all persons present to hear the distant party’s responses. 
TO USE GROUP LISTENING 
1) With the handset off-hook, press and hold the m 
button then place the handset on-hook and release the 
m button. 
l SPEAKER and MIC LEDs light and the distant party’s 
voice is heard via the telephone’s speaker. 
2) When local response is required, lift the handset off-hook. 
l SPEAKER and MIC LEDs go off. 
l Telephone speaker is silenced. 
l...

FEATURE USE 
AUTO BUSY REDIAL (continued) 
TO CANCEL ABR 
Press the m button (or m 1 I). 
NOTES: 
1. ABR will not be attempted while the station is busy on 
another call but will continue to time-out. 
2. With each attempt: 
The CO (or IiT) and SPEAKER LEDs blink when the 
line is seized. 
Dial tone is heard via the speaker. 
Telephone number is redialed. 
If busy, ABR will reset and try again. 
If a connection is made, ring tone sounds until called 
party answers. 
If the originatin station does not...

FEATURE USE 
FEATURE USE 
SPEED DIAL BUTTONS TELEPHONE NUMBER STORAGE (continued) 
PROGRAMMABLE OPTION (continued) 
2. Repeat this procedure to replace the stored telephone 
numbers with new ones. 
3. It may be necessary to insert a pause after the CO line 
access code to allow for dial tone delay. If so, press the 
m (arm button after entering the Centrex or 
PBXaccesscode (see Telephone NumberStorage-Pauses). 
4. To store * or # DTMF tones in speed dial numbers, the 
tele hone that is used to store the...

FEATURE USE FEATURE USE 
TELEPHONE NUMBER STORAGE (continued) TELEPHONE NUMBER STORAGE (continued) 
STORING A STATION SPEED DIAL NUMBER 
Speed dial telephone numbers can be stored by each station. 
1) Do not lift the handset. 
2) Press the [ and i (or m and m) buttons, respec- 
tively. 
3) Dial a 2-digit speed dial code. 
l Station speed dial codes run consecutively from 10 N 
49. 
4) Dial the telephone number to be stored (20 digits maxi- 
mum). 
5) Press the 1 button to record the number in memory. 
6)...

FEATURE USE 
FEATURE USE 
TONE/PULSE DIALING 
PROGRAMMABLE OPTION (continued) 
TO CHANGE TO TONE SENDING 
After you have dialed a telephone number and the call is in 
progress, press the m button. 
TONE LED goes on. 
Pressing the dialpad buttons will cause DTMF tones to be 
transmitted. 
NOTE: 
After :hem button is pressed, the Tone LED will remain 
on and DTMF tones will be sent when dialing until the call 
is released. When originating or receiving a new CO line 
call, the system automatically places...

FEATURE USE 
INTERCOM CALLS (continued) 
MICROPHONE CUT-OFF 
PROGRAMMABLE OPTION 
l INT LED flashes green at the In-use rate. 
3) Dial the desired station number. 
l You hear a single ring tone. 
4) Speak when the ring tone ends. 
5) Hang up when the call is completed. 
NOTES: 
1. See Automatic Off-hook Selection. 
2. Tone Signaling can be accomplished by dialing0 after 
the station number. 
TO RECEIVE AN INTERCOM CALL 
1) You hear a single long tone, followed by the caller’s voice. 
l INT LED flashes...

FEATURE USE FEATURE USE 
CALL TRANSFER WITH CAMP-ON CALL TRANSFER WITH CAMP-ON (continued) 
Allows you to transfer an outside call to a station that is either idle 
or busy. 
TO TRANSFER A CALL 
1) While connected to an outside call, press them 
button. 
l CO LED remains green, but changes to the Confer- 
ence fast flash rate. 
l INT LED flashes at the In-use rate. 
2) Dial the station number to which the call is to be transferred. 
3A) If the called station is idle: 
l You hear a single ring tone. 
4A)...

FEATURE USE FEATURE USE 
CALL TRANSFER WITH CAMP-ON (continued) CONFERENCE CALLS (continued) 
TO ANSWER A TRANSFERRED CALL (if your station is 
busy) 
1) You will hear a l-second warning tone. 
l The outside call is camped-on to your station. 
l CO LED flashes green at the On-hold rate. 
2) You have several choices: 
a) Press the appropriate 
q button. 
l Existing call is terminated. 
l The new line is answered and its LED changes to 
the In-use flash rate. 
bl) Hang up. . . . or. . . 
l Existing call is...

FEATURE USE 
FEATURE USE 
CONFERENCE CALLS (continued) CALL FORWARD-ALL CALLS (continued) 
TO CONFERENCE UP TO FOUR STATIONS ON ONE 
INTERCOM LINE 
1) Establish a two-station intercom call. 
2) Press them button. 
l You hear intercom dial tone. 
l INT LED flashes green at the Conference rate. 
3) Dial the third station’s number. 
4) Press the m button after the party answers. 
l INT LED flashes at the In-use rate. 
l All parties will be conferenced. 
5) To add the fourth party, repeat steps 2 N 4. 
CALL...