Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

MESSAGE SENDING (continued) MESSAGE SENDING (continued) 
TO SET A MESSAGE IF YOU DO NOT HAVE Am BUTTON 
1) Press the m button. 
l The INT LED liahts. 
2) DialBI. y 
3) Dial the number of the message you want (see Note). 
4) Press the m button. 
l The INT LED goes out (your message is now stored). 
NOTE: 
Personal (10 - 19) and system (60 - 99). 
TO CANCEL A MESSAGE THAT HAS BEEN SET AT YOUR 
STATION 
Press the m button. 
l The MSG LED goes out. 
TO CANCEL A MESSAGE IF YOU DO NOT HAVE A m 
BUlTON 
1)...

MESSAGE DIRECTORY USER NAME/NUMBER DIRECTORY 
Messages are limited to 32 alphanumeric characters and are 
displayed in two rows of 16. 
This directory is provided for reference and recording messages. 
Message # 
Message # 
Message # 
Message # 
Message # 
I 
Message # 
Message # 
NAME/NUMBERS are limited to 16 alphanumeric characters and 
are displayed on the top row of idle LCD stations and the bottom row 
of called LCD stations. 
This directory is provided for station 200 reference and recording of...

SPEED DIAL MEMO DIRECTORY 
Speed Dial memos are limited to 12 characters for the memo (top 
row of LCD) and 16-digits/pauses for the dial number (bottom row 
of LCD). 
This directory is provided for recording Speed Dial numbers with 
memos. 
* Code: 12-Character Memo: (Example) 
* 10 -MEMO HERE 
SPEED DIAL# HERE 
* 
* 
* 
, 
* 
* * Code: 12-Character Memo: 
* 
* 
* 
* 
* 
EEE 
35  

* Code: 
* 12-Character Memo: 
* 
* 
* 
* 
* 
 
* .- * Code: 12-Character Memo: 
* 
* 
* 
* 
* 
* 
* 
36 _* i” 37  

* Code: 
* 12-Character Memo: 
* 
* 
* 
* 
* 
r 
* - INDEX 
Adding to a Preprogrammed Message ................................. 18 
Busy Field Display ................................................................ 16 
Busy Station Messaging ....................................................... 30 
Call Forward Display.. ........................................................... 13 
Called Station Messaging ..................................................... 27 
Calling Station Messaging...

TOSHIBASYSTEM PRACTICES 
ELECTRONICKEYTELEPHONESYSTEM STRATADKFAULTFINDING 
SECTlON200-096-500 
FEBRUARY1991 
Stratalzx 
RELEASE 1,2, and 3 
FAULT FINDING PROCEDURES  

PARAGRAPH SUBJECT 
1 
2 
3 
4 
5 
6 
7 
7.01 
7.10 TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i 
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 
FAULT CLASSIFICATION . ....

1 GENERAL IMPORTANT! 
1 .Ol This section describes the maintenance pro- 
cedures used to diagnose faults in the STRATA DK 
digital key telephone system. Faults are classified 
and then cleared by replacing the malfunctioning 
unit and performing operational tests in the se- 
quences prescribed by the fault clearing flowcharts 
in Paragraph 5. 
Many system features are assigned, en- 
abled or disabled using software entries 
as described in 
Programming Procedures. 
It is important to verify that the...

STRATA DK FAULT FINDING 
SECTION 200-096-500 
FEBRUARY 1991 
3.05 The flowcharts are sequentially arranged to 
permit rapid fault localization within the system. 
All 
fault clearing must begin with the Fault Classifica- 
tion Flowchart, which is arranged in the correct fault 
locating sequence. 
3.06 The following precautions must be observed 
when handling PCBs: 
DO NOT: 
l Drop a PCB. 
l Stack one PCB on top of another. 
l Handle a PCB without discharging any static 
electricity from your person by...

STRATA DK FAULT FINDING 
SECTION 200-096-500 
FEBRUARY 1991 
problem. The Power Supply Test Procedure in 
Paragraph 3, Section 200-096-205, Installation, can 
be employed to further isolate possible causes 
before removal of the KSU back cover or the power 
supply unit. Figure 2 shows backplane connector 
Pl and P4 and voltages at each pin. Voltages 
should fall within the following ranges: 
Nominal Range 
-24V -26.3 - -27.8 
+5v +4.5 - +5.5 
-5v -4.5 - -5.5 
6.02 If voltage checks indicate a power...