Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

REMOTE ADMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
LOCAL 
TERMINAL 
PPTC 
MODULAR TO DB25 
/ ADAPTOR 
RS-232 
I (300 OR 1200 PBS) 
I 50‘ FEET MAX. 24 AtiG 
KSU 
. 
_ p’ou(s) INTERNAL 
See Peripherals Installation, Section 200-096-208, 
for detailed pin-out information. 
5.20 Local Operation 
5.21 
Use the procedure below to establish com- 
munications between the local terminal and the 
PIOU(S) so that programming may be accom- 
plished via the terminal. 
NOTE: 
Hereafter, whenever the...

nal or PC (as described in Paragraph 5). It must 
interface with the public telephone network and be 
compatible with Bell 103 or 212 modem specifica- 
tions. 
6.10 Set-up 
6.11 
Refer to Figure 1 and verify that the remote 
terminal is connected and set-up as follows: 
1) Connect the terminal and modem together 
with the RS-232 cable. 
NOTE: 
If a personal computer is being used, connect 
the cable to the serial “C0M”pot-t. 
2) 
3) 
4) 
5) 
Connect the modem line input to a CO/PBX 
line for access to...

REMOTE ADMIN 81 MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
2) Press the q key. 
l The system responds, and the terminal 
displays: 
DKTS VERSION 1.0 (DK CONNECT) R2 
XODE 
* The software version number is identified in 
Program 00. 
3) Enter the 4-digit security code and press the 
q key. 
l The system responds, and the terminal 
displays: 
OK 
MODE 
7 MODE SELECTION 
7.00 Selecting a Mode 
7.01 To enter an operating mode, establish com- 
munication with the terminal, enter the security 
code,...

8.30 Multiple Station (Range) Programming 
8.31 
Some programs select options for individual 
stations (where 0 0 represents the port number 
being programmed). To save time, it is possible to 
program all ports or a range of ports simultane- 
ously. 
8.32 Multiple station programming is accomplished 
by substituting a range of ports (0 0 10 0) for 
the port number part (0 0) of the program. 
Example, all ports: w 1 111 
8.33 When the multiple station range is entered, 
the terminal displays existing...

REMOTE ADMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
dialing codes for either an individual station, 10 0 .\, 
>MODE DUMP (all stations and system data) 1 m B (system data .’ 
D MSG SYS only). 
. 
SYS M60 OUT TO LUNCH 9.05 LCD Messages Dump: While in the dump 
SYS M61 IN A MEETING mode, enter “MSG” and two or three characters 
SYS M62 CALL 
SYS M63 BACK AT and press q . The characters represent stored 
SYS M64 RETURN ON messages for either an individual station, 101 (all 
SYS M65 stations...

REMOTE ADMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
IMPORTANT! 11 .lO Remote Called Station Message Mode 
Any electronic telephone button can be 
activated from the remote terminal at any 
time while in the Test Mode (even while the 
end user is using the electronic telephone). 
Therefore, caution must be used toprevent 
service interruption or interference. The 
Test Mode provides status tests to check 
whetherornotastationorCOlineisinuse. 
The status checks should always be made...

REMOTE ADMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
12 SPEED DIAL MODE 
12.00 General 
12.01 The Speed Dial Mode can be used to add or 
change speed dial numbers to any of the system 
speed dial memory locations (60 N 99) and to any 
station speed dial memory locations (IO w 49). 
12.02 Chain speed dial numbers can also be 
programmed using the Speed Dial Mode. See the 
Electronic Telephone User Guide for more infor- 
mation regarding chain speed dialing operation. 
12.03 To program...

REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-C 
PROGRAM90 
INITIALIZING PROGRAMS 00 - 97 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 
Enter the Program Mode >MODE PROG 
At the >MODE prompt enter 1 1 H 1 
q . 
2 Enter Program Number 90 P 90 
Press 
q . P90 
3 To Initialize All Programs Enter 1 1 i 1 0 P90 00-97 
NOTE: Single programs can be initialized by entering a single 
program number plus B . Group numbers are separated by an 1 . 
4 Enter key number 1 0. P90 00-97 01 N 
5 Change 01...

REMOTEADMIN & MAINTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-D 
PROGRAM92 
STATION SPEED DIAL, SPEED DIAL MEMO,VMID CODES 
INITIALIZATION . 
iTEP ACTION DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter i m m B 
q . 
2 Enter Program Number 92 P 92 
Press 
q . P92 
3 Enter 0 . P92 
P92 1 
4 Enter key number: 1 0. P92 
P92 1 01 N 
5 Change key 01 to “ON” by entering 0 . P92 
P92 1 01 N Y 
6 Press m two times. P92 
P92 1 01 N Y 
02 N 
03 N 
7 Change key 03 to “ON”...

REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
- 
- 
- 
- 
- 
- 
- 
L 
TABLERM-E 
PROGRAM 92(continued) 
SYSTEM SPEED DIAL, SPEED DIAL MEMO INITIALIZATION 
;TEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter w m 1 B 
q . 
2 Enter Program Number 92 P 92 
Press 
q . P92 
3 Enter 1 . P92 
P92 2 
4 Enter key number 1 0 . P92 
P92 2 01 N 
5 Change 01 key to “ON” by entering 1 . P92 
P92 2 01 N Y 
6 Press m three times. P92 
P92 2 01 N Y 
02 N 
03 N 
04...