Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

REMOTE ADMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
TABLE RM-AW 
PROGRAM 55-O 
LCR MODIFIED DIGITS-DELETE . 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter B m B 1 
q . P 
2 Enter Program Number 55 P 55 
Press 
q P55 
3 Enter Modified Digits Table Number P55 1 
Refer to the System Record Sheet and enter the modified 
digits table number (1 - 6). 
Example: Enter modified digits table number 1, entern . 
4 Enter Code 0 P55 10 00 10 
The system...

REMOTEADMIN &MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AX 
PROGRAM55-1 
LCR MODIFIED DIGITS-ADD 
;TEP ACTION 
DISPLAY/PRINTOUT 
I Enter Program Mode 
>MODE PROG 
At the >MODE prompt, enter i m m a 
q . P 
2 Enter Program Number 55 P 55 
Press 
q . P55 
3 Enter Modified Digits Table Number P55 1 
Refer to the System Record Sheet and enter the required 
modified digits table number (1 - 6). 
Example: Enter table number 1, enter [ . 
4 Enter Code 1 P55 11~~~ (up to22 digits) 
The system...

REMOTEAOMIN & MAINTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AY 
PROGRAM 55-2 
LCR MODIFIED DIGITS-END 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the >MODE prompt, enter B H B 1 
q P 
2 Enter Program Number 55 P 55 
Press 
q . P55 
3 Enter Modified Digits Table Number P55 1 
Refer to the System Record Sheet and enter the required 
modified digits table number (1 - 6). 
Example: Enter table number 1, enter 0. 
4 Enter Code 2 p55 12 nnn (up fo22digifs) 
The system will...

REMOTEADMlN&MAlNTPROCEDURES 
SECTION 200-096-600 
FEBRUARY1991 
TABLERM-AZ 
PROGRAM56 
LCRSTATIONGROUPASSIGNMENT 
STEP1 ACTION 
I DISPLAY/PRINTOUT 
1 Enter Program Mode >MODE PROG 
At the z-MODE prompt, enter w a 1 H 
q . P 
2 Enter Program Number 56 P 56 
Press (9 P56 
3 
Enter Port Number 
4 
Refer to the System Record Sheet and enter the 
required port number, [70 or 00 Ino. 
Example: Port 01, enter 1 0. 
Press OKey (if single port 00 entry in step 3). 
The system will display any previously entered...

REMOTE ADMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
TABLE RM-BA 
PROGRAM DATA DUMP 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Data Dump Mode >MODE DUMP 
At the >MODE prompt, enter 1 m m 1 
q . D 
2 
To Output Program Data 
Enter 1 g Inn q 
D PROGun 
00 = Program number or 110 for all programs. 
3 
I I 
To Stop Printout at Any Time 
Enter JrRr=ll$m . 
TABLE RM-BB 
SPEED DIALING DATA DUMP 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Data Dump Mode 
>MODE DUMP 
At the >MODE prompt, enter 1...

REMOTEAOMIN &MAlNTPROCEDURES 
SECTlOti200-096-600 
FEBRUARY1991 
TABLERM-BC 
LCOMESSAGING DATADUMP 
STEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Data Dump Mode 
>MODE DUMP 
At the >MODE prompt, enter m 1 m i 
q . 
* 
To Output Message Data 
D MSGnuu 
Enter @ H H nnn q ---or--- m 1 100 q 
mo =m or 8i8 
00 = Pot-t number of individual station. 
3 
I / 
To Stop Printout at Any Time D 
Enter mm 
I 
-51-  

REMOTE AOMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
TABLE RM-BD 
MODE 95 
REMOTE CALLING STATION MESSAGING (ADD/REVIEW/CHANGE) . 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Message Mode >MODE MESG 
At the >MODE prompt, enter m 0 1 a 
q . 
2 
To Add Or Review a Calling Station Message m 95 
Set the terminal keyboard to the lower case (cap lock off) and 
enter QII. 
NOTE: 
Enter “m” anytime it is desired to start over in this procedure. 
3 Enter 1 1 1 (XXX = station number where the...

REMOTEADMlN&MAlNTPROCEDURES 
SECTlON200-096-600 
FEBRUARY1991 
TABLERM-BE 
MODE97 
REMOTECALLINGSTATION MESSAGlNG(ADD/CHANGE) 
TEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Message Mode 
>MODE MESG 
At the >MODE prompt, enter m 0 lI[9 
. 
2 
To Add a Message (or change a previously stored message) 
m 97 
Set the terminal keyboard to lower case (caps lock off) and 
enter 110 
NOTE: 
Enter I’m” at anytime it is desired to start over in this procedure. 
3 Enter 1 1 0(XxX = station number for which the message...

REMOTE AOMIN & MAINT PROCEDURES 
SECTION 200-096-600 
FEBRUARY 1991 
TABLE RM-BF 
MODE 94 
REMOTE CALLED STATION MESSAGING (ADD/REVIEW/CHANGE) . 
iTEP ACTION 
DISPLAY/PRINTOUT 
1 Enter the Message Mode >MODE MFSG 
At the >MODE prompt, enter m 0 1 H [9 . 
2 
To Add Or Review a Called Station Message m 94 
Set the terminal keyboard to the lower case (cap lock off) and 
enter min. 
3 Enter 0 1 0(XxX = Destination station number or destination m94 xxx 
group number [30 = all stations, 31-34 per system,...

STEP 
1 
2 
6 
7 
8 
REMOTEADMIN &MAlNTPROCEDURES 
SECTlON200-096-600 
FEBRUARY1991 
TABLERM-BG 
MODE96 
REMOTECALLEDSTATION MESSAGlNG(ADD/CHANGE) 
ACTION 
Enter the Message Mode 
At the >MODE prompt, enter fl 0 a H q . 
To Change or Add a New Called Station Message 
Set the terminal keyboard to the lower case (cap lock off) and 
enter Q[I 
NOTE: 
Enter “m” (lower case) anytime it is desired to start over 
in this procedure. 
Enter 1 1 13 (XXX = destination station number or destination 
station group...