Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
NOTE: 
Program 92-5 (LEDs 0 1 and 05) does not 
affect receiver handset volume levels. 
l Dial Pulse (DTMF Off), LED Ii-If any 
device connected to a PSTU or PESU port 
does not require the CRCU for DTMF de- 
coding, it should be programmed for dial 
pulse. When that device goes off-hook, the 
CRCU will not be accessed, thereby re- 
ducing potential traffic to the CRCU. 
l Change DISA Security Code, LED lo- 
This allows...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
should have the following LEDs turned ON: 04, 
05, 09, 15, 16, 17, 18, 19, 20. These LED’s 
should be set ON for VM ports only, not for 
telephone ports. 
NOTE: 
LED 04 may be ON or OFF, depending on 
VM/AA device operation. See the LED 04 
write up that follows. 
l INTOUCH (B + Station Number), LED 
20-This feature is associated with an 
INTOUCH Digital Voice Messaging Sys- 
tem connected to a PSTU or PESU port. 
DTMF...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
I . 
I 
I . 
0 
0 
0 
long time in time-out situations. 
Group Page 1 - 4, LEDs 11 w 14-lnter- 
corn paging can be directed to digital and/ 
or electronic telephone speakers in a group 
arrangement. Up to four groups are pos- 
sible. This program assigns each 
electronic and digital telephone to the 
groups. An electronic or digital telephone 
can be assigned to as many groups as 
desired. 
All Call Page...

SECTION 200-096-302 
FEBRUARY1991 
I 
be accessed, standard telephones always 
receive system intercom dial tone when 
originating calls. 
Program 33-Station Hunting (Voice Calls 
Only): 
If a station is busy, Station Hunting 
allows the ringing of an alternate station as 
defined by the assignments in this program. If 
the hunted to station is busy, the system will try 
to ring the next hunt to station, and so on. If a 
hunt to station is in call forward, the call forward 
overrides the hunt. A CO Line...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
the flexible buttons (10 or 20) can be 
programmed. 
Program 40-Station CO Line Access: Any 
station can have access to as many CO lines 
as desired. Any station denied access (either 
to make a call orto answer a call) to a CO line 
cannot seize that line by dialing an access or 
pickup code or by using a CO line button. This 
also denies access via Least Cost Routing. 
Use this program to divide CO lines for Tenant...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
Program 69 conflict (duplicate) with emer- 
gency or other type telephone numbers 
set in 
Program 44A, Program 44A has 
priority. 
3. Toll Restriction and DISA parameters re- 
quirements are not affected by this 
program. 
Programs 45 - 48 Toll Restriction: All Toll Re- 
striction program information is provided later 
in this chapter. 
Programs 50 - 56-Least Cost Routing: All 
Least Cost Routing program information is...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
Restriction Class can be assigned with 
Program 70 to each of the 300 Verified 
Account Codes. 
l Verified Account Code Dial Require- 
ment (Release 3)-Verified Account Code 
Dial Requirement is assigned on a station- 
by-station basis in Program 30, LED 140N. 
All Account Codes dialed (forced or volun- 
tary) from stations assigned in this pro- 
gram will be verified. 
l Code Change-Stations selected in Pro- 
gram 30,...

PROGRAMMINGPROCEDURES-INSTRUCTIONWSYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
PEPU can be assigned to operate with the 
Door Lock function or with External Page 
for mute control. The door lock button is 
assigned in 
Program 39; the door lock 
activation time is assigned in 
Program 
77-1. 
This door lock function is not associ- 
ated with the HDCB door lock; it is an 
addition to HDCB door locks. 
l NT Relay, LED 06-A relay, located on the 
PIOU, PIOUS or PEPU, can be assigned to 
operate in one...

NOTE: 
An optional security code for DISA outgoing 
CO calls is available via Program 60-6. 
l Ring IMDU Maintenance Modem, Fea- 
ture 
5-IMDU Remote Maintenance mo- 
dem can be accomplished with this pro- 
gram. Different alternatives are available 
for the system modes of DAY, DAY2, and 
NIGHT. If none of these are selected, the 
IMDU can still be reached on station 19 
with the DISCDISA feature or by a Ring 
Transfer from the DSS console attendant 
or any other station. IMDU station 19 must 
be...

PRDGRAMMlNG PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS 
SECTION 200-096-302 
FEBRUARY 1991 
for individual stations. Toll Restriction can also be 
enabled/disabled for each outgoing CO line in the 
system. Exception office code access is accomplished with 
the Six-digit Toll Restriction method described 
earlier. . 
3.02 Simple Toll Restriction: The first method, 
Simple Toll Restriction, only involves the first digit 
dialed. The system can be programmed to reject 
outgoing calls beginning with 
0 or 1 (see...