Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

PROGRAMMINGPROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
PARAGRAPH 
1 
2 
2.10 
2.20 
3 
3.10 
3.20 
3.30 
3.40 
4 
4.10 
4.20 
4.30 
TABLE 
I-A 
I-B 
I-C 
I-D 
I-E 
I-F 
I-G 
FIGURE 
l-l 
l-2 
l-3 
l-4 
l-5 
l-6 
TABLEOFCONTENTS 
SUBJECT 
TABLE OF CONTENTS 
............................................................................... 
PURPOSE .................................................................................................... 
ORGANIZATION...

1 PURPOSE 
1 .OI 
The purpose of this programming section is to 
provide the system installer with instructions to set 
the detailed feature configuration and operation of 
the system. 
1.02 This chapter provides an overview of the 
programming section, its organization, and its 
general programming instructions. 
1.03 For easy reference, every paragraph is 
numbered. 
2 ORGANIZATION 
2.00 This programming section is organized in 
modular chapters. The chapters are titled as fol- 
lows: 
2.10 Chapter...

PROGRAMMING PROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
another vowam 
more data 
1 
~T;l~T;l~~s,,,n~~fispKRIg*~!~lT;;lT;;l~!SPKR~~~ 
/~--7--\---T-- 
Step 1 Step 2 Step 3 
Step 4 Step 5 
Enter Program Mode Enter Program Number Enter Program Data Exit Current Program Exit Program Mode 
\, 
; * I 
-: 
‘0 :- (LED buttons) 
-. 
I 
and/or 
tl-II 
FIGUREI-I-PROGRAMMINGBUTTONSEQUENCEOVERVIEW 
3.23 Multidimensional Programs: 
Once a pro- 
gram number is entered, the first dimension (usu- 
ally a...

PROGRAMMINGPROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
TABLEl-A 
SIMPLEPROGRAM: PROGRAM33 
(STATION HUNTING) 
I 
Press... 
Step 
m + LED keys 
#’ Action description LCD RESPONSE . . . 
1. Use the programming LCD electronic or digital telephone 
NO. 205 
connected to port 05 - circuit 6. JAN 20 SUN 
06:43 
Make sure the programming button strip template is 
installed on the programming telephone (see 
Paragraph 3.24). 
2. HmlEBE~ 
Enter programming mode. 
3. mII= PROGRAM MODE 
Access...

PROGRAMMINGPROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
TABLEl-B 
MULTIDIMENSIONALPROGRAM: PROGRAM30 
(STATION CLASS OFSERVICE) 
Press... 
Step 
m + LED keys 
# 
Action description LCD RESPONSE . . . 
I 1. Use the programming LCD digital or electronic 
NO. 205 
telephone connected to port 05 - circuit 6. JAN 20 SUN 
06:43 
Make sure the programming button strip template is 
installed on the programming telephone (see 
Paragraph 3.24). 
2. m[[E[ 
PROGRAM MODE 
Enter programming mode. 
3....

PROGRAMMINGPROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
TABLE I-B (continued) 
MULTIDIMENSIONALPROGRAM: PROGRAM30, 
STATION CLASSOFSERVICE 
Press... 
Step 
m + LED keys 
# 
Action description LCD RESPONSE . . . 
6. LED keys 01 - 20 (continued) 
LED 12 and 13: Digital Telephone Handset Receiver 
Volume (Release 3). 
LED 14: Account Codes Verified (Release 3). 
LED 15: Verified Account Code Revision Authority 
(Release 3) 
LED 16: Traveling Class of Service Code Revision 
Authority (Release...

PROGRAMMING PROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY 1991 
0 
I . 
0 PCTU or PCTUS (Common Control Unit PCB): 
A PCTU or PCTUS must be installed, and have 
its jumpers set for live operation. 
PEKU, PESU, or PDKU in slot 01 
LCD program telephone connected to port 05, 
equipped with programming template. 
3.33 Minimum Software Requirements: To pre- 
pare the system software for programming, clear 
the memory by initializing its data (with 
Programs 
90 and 92), as specified in this Section,...

PROGRAMMINGPROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
TABLE14 
PROGRAM90 
. 
INITIALIZING PROGRAMS 00- 97 
Press... See Program 90System Record Sheet 
Step m + LED keys 
# Action description LCD RESPONSE . . . 
1. Use the programming LCD electronic or digital telephone 
with programming template connected to port 05 - circuit 6. NO. 
205 JAN 20 SUN 06:30 
2. ImEW PROGRAM MODE 
Enter programming mode. 
3. ~~~~ 
Access Program 90. System beeps after m PROGRAM = 90 
DATA STORE 
button is...

PROGRAMMING PROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
. 
EXITprogramming mode 
 If all programs 
 Enter programming mode Program(s) to be initialized 
END Program 90 for 5 sec. then 
Button I and 2 LEDs must be lit POWER ON 
Initialize Programs 00 - 97 every time: 
l Installing a new system 
l To bring a system’s programming back to the default setting. 
Specify the range as follows: 
maHaT; 
To initialize one program at a time, enter just the individual program number, then 1....

PROGRAMMINGPROCEDURES-INTRODUCTION 
SECTION 200-096-301 
TABLE14 FEBRUARY1991 
PROGRAM92 
INITIALIZING SPEED DIAL NUMBERS, ID CODES, 
. 
CHARACTERMESSAGEMEMORY,TlMED REMINDERS, 
D;GITALTELEPHONEVOLUME,ANDCALLFORWARD BACKUPMEMORY 
. . . 
Step m + LED keys 
# Action description 
LCD RESPONSE . . . 
1. Use the programming LCD electronic or digital telephone 
NO. 
205 with programming template connected to port 05 - circuit 6. JAN 20 SUN 06:43 
2. 
HmEBEB PROGRAM MODE 
Enter programming mode. 
System beeps...