Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

PROGRAMMING PROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY 1991 
more data 
Enter programming mode 
SELECT= (as below, ED ProgreT 7- 
Specify if initializing Station Autodial, EXIT programming 
System Autodial,Character Message mode 
Memory or Timed Reminders: 
p-$J@)L Clears Station Speed Dial, Voice Mail ID Codes, 
and LCD memos Assigned to Station Speed Dial numbers. 
pJ%J@ Clears System Speed Dial and LCD memos assigned to 
System Speed Dial numbers. 
Clears Character Message Memory (Station...

PROGRAMMING PROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
TABLEl-E 
PROGRAM03 
Press... FLEXIBLEPCBSLOTASSIGNMENTS 
Ster, m + LED keys 
ft’ I, Action description LCD RESPONSE . . . 
1. Use the programming LCD electronic or digital telephone 
NO. 205 
with programming template connected to port 05 - circuit 6. JAN 20 SUN 
06:43 
2. WmE~P~ PROGRAM MODE 
Enter programming mode. 
3. moom 
Access Program 03. After m key is pressed, system PROGRAM = 03 
DATA STORE 
beeps to indicate program...

PROGRAMMING PROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
TABLEI-F 
PROGRAM00 
SOFTWARECHECKANDREMOTEMAINTENANCESECURITYCODEASSIGNMENTS 
Press... 
Step 
w + LED keys 
ti 
Action description 
LCD RESPONSE . . . 
I 
1. Use the programming LCD electronic or digital telephone 
NO. 205 
with programming template connected to port 05 - circuit 6. 
JAN 
20 SUN 06:43 
2. mElWEB PROGRAM MODE 
Enter programming mode. 
3. =Iim PROGRAM = 00 
Speaker beeps to indicate when to enter program 
DATA STORE...

PROGRAMMING PROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY 1991 
TABLE 1-F (Continued) 
PROGRAM 00 
SOFTWARE CHECK AND REMOTE MAINTENANCE SECURITY CODE ASSIGNMENTS 
Press... 
Step B + LED keys 
Action description 
8. filrmr;l LCD RESPONSE . . . 
00 SELECT = ## 
Secure Program 00 data in system memory. DATA PROGRAMMED 
9. m PROGRAM = 
Exit Program 00. Enter another program number (see 
Table D), or exit programming mode (go to step IO). 
System.beeps to-indicate it’s exiting Program do. 
10. ljm...

PROGRAMMING PROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
TABLEl-G 
PROGRAM04 
Press... PORT/STATIONNUMBERASSlGNMENT 
m + LED keys 
#’ Action description LCD RESPONSE . . . 
I. Use the programming LCD electronic or digital telephone 
NO. 205 
with programming template connected to port 05 - circuit 6. JAN 20 SUN 
06:43 
2. 5mEEEclo PROGRAM MODE 
Enter programming mode. 
3. ~~~~ 
Access Program 04. System beeps after m PROGRAM = 04 
DATA STORE 
is pressed to indicate a program number may be...

PROGRAMMINGPROCEDURES-INTRODUCTION 
SECTION 200-096-301 
FEBRUARY1991 
HOW TO SET THE DATE 
The date must be set from the electronic or digital telephone assigned to Port 00. 
Press the following button sequence with the handset on the hook: 
Date in year/month/day ( 
format (YYMMDD). If month 
or day is a single digit, precede 
with a zero (0). If the electronic 
telephone has a 
Redial button 
programmed, press 
it instead. 
FIGUREI-4-SETTING SYSTEM DATE 
HOW TO SET THE TIME 
The time must be set from...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
trata@mx 
RELEASE 1,2, and 3 
PROGRAMMING PROCEDURES 
CHAPTER TWO 
INSTRUCTIONS/RECORD SHEETS  

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
IMPORTANT INITIAL INSTALLATION NOTES: 
These minimum installation steps must be carried out for proper system operation. 
0 
7. Set PCTU jumper for 
BATTERY OPERATION; otherwise, all programmed customer data will 
be lost on power down. 
2. Place PEPU, PIOU, or PIOUS PCB in highest slot number of KSU, 
3. Place all other PCBs in KSU from lowest slot number to highest in the following order: 
I PCTU or PCTlJSl (always...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
TABLEOFCONTENTS 
1 
1.10 
1.20 
2 
3 
3.00 
3.10 
1 f.10 
4.20 
4.30 
4.40 
4.50 
4.60 
4.70 
4.80 
4.90 
4.100 
5 
6 
6.00 
6.20 
7 
7.10 
7.20 
7.30 
7.40 
PAGE 
i 
ii 
2-l 
2-l 
2-l 
2-19 
2-19 
2-19 
2-20 
2-20 
2-21 
2-21 
2-22 
2-22 
2-23 
2-23 
2-23 
SUBJECT 
IMPORTANT INITIAL INSTALLATION 
NOTES .......................................... 
TABLE OF CONTENTS...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
TABLELIST 
TABLE SUBJECT 
PAGE 
2-A PROGRAMS 00 w 97 IN NUMERICAL ORDER WITH 
SECTIONS CROSS-REFERENCED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
2-43 
2-B ACCOUNT CODE PROGRAM OPTION MATRIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
2-153 
2-c OVERRIDE OPTION MATRIX 
. . . . . . . . . . . . . . . . . . . . . . ....