Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SiCTlON 200-096-302 
FEBRUARY1991 
be routed differently than the overall area 
code. 
l Enter the specific office codes that are to 
be routed differently. 
Example 2-m the second example, the route 
plan only applies to office code exceptions. The 
first office code exception table may be docu- 
mented on the LCR Plan record sheet: 
l Check the box on the record sheet next to 
Office Code Exception Table number. 
l Enter the number of the exception...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
ing CO line access to stations, including 
LCR access. 
l Program 41 allows CO line access to sta- 
tions using LCR only for outgoing calls 
when enabled. 
2: Modified Digits Table (1 W 6): Refer to Pro- 
grams 
55-0, 55-l and 55-2. The system 
handles CO line groups differently, according 
to which modified digits table was assigned in 
Program 54. 
7.40 Program 55 Series-LCR Modified Digits 
Tables 
7.41 
This program...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTlON200-096-302 
FEBRUARY1991 
SYSTEM RECORD SHEETS 
RELEASE 1,2, and 3 
2-33  

PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
IMPORTANT INITIAL INSTALLATION NOTES: 
These minimum installation steps must be carried out for proper system operation. 
1. 
2. 
3. 
I 
4. 
5. 
6. 
1. 
2. 
3. Set PCTU jumper plug for BATTERY OPERATION; otherwise, all programmed customer 
data will be lost on power down. 
Place PEP& PIOU, or PIOUS PCB in highest slot number of KSU. 
Place all other PCBs in KSU from lowest slot number to highest in the following order:...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
STRATADKSOFTWARERELEASES 
Software Guide: This is a reference guide that provides updated information regarding software enhancenients to 
the STRATA Digital Key (DK) System. 
DKSoftware Identification: The DKoperating software is stored on Read Only Memory (ROM) chips and is identified 
by ROM Version. 
There are four ROM chips in a DK ROM set, which are installed on a processor control circuit PCB. There are four...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
RELEASE2(R2)SOFTWAREGUlDE 
With the exception of Busy and Group Station LCD Messaging, all items available with RI software ‘-3, 
are available with R2 software; items listed below are available with R2 software and above only. -*’ 
Item Description *Related Programs 
Comments 
PESU PCB OJ, Code 25 and 26 
Station PCB, supports 2 standard 
telephones, 4 electronic telephones 
BGM/MOH separation 10-2, key/LED 09...

PROGRAMMINGPROCEDURES-INSTRUCTIONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
RELEASE2(R2)SOFTWAREGUlDE (continued) 
With the exception of Busy and Group Station LCD Messaging, all items available with RI software 
are available with R2 software; items listed below are available with R2 software and abbvi! only. 
Item Description 
80/160 DTMF option for VM ID 
Codes 
Immediate drop when Toll 
Restricted digits are recognized 
CO line, incoming ring detector 
time change: (120/223 ms) 
ABR...

PROGRAMMINGPROCEDURES-INSTRUCTlONS/SYSTEMRECORDS 
SECTION 200-096-302 
FEBRUARY1991 
RELEASE3(R3)SOFTWAREGUlDE 
All items available with RI and R2 software are available with R3 
software; items listed below are available with R3 software only. 
Item Description 
Night ringing over selected 
page zones 
*Related Programs Comments 
77-1, key/LEDs 10 - 13 
Allows CO lines to ring over selected PIOU 
B,i -3 
page zones. CO lines can be placed into 
two groups (tenant 1 and tenant 2), and 
each group can be...

PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS 
SECTION 200-096-302 
FEBRUARY 1991 
RELEASE 3 (R3) SOFTWARE GUIDE (continued) 
All items available with RI and R2 software are available with R3 
software; items listed below are available with R3 software only. 
Item Description *Related Programs 
Comments 
PDKU PCB 
OJ, Code 62 and 64 Station PCB, supports 8 Toshiba digital 
telephones (DKT) or 7 DKTs and one 
digital, direct station selection console 
(DDSS). Also supports up to 8 stand-alone 
data...

PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS 
SECTION 200-096-302 
FEBRUARY 1991 
RELEASE 3 (R3) SOFTWARE GUIDE (continued) 
All items available with RI and R2 software are available with R3 
software; items listed below are available with R3 software only. 
Item Description *Related Programs Comments 
Emergency number override of 
verified/forced account code 44A (51 - 53) 
- Allows up to three emergency numbers 
(911, etc.) to be programmed to bypass 
the forced (verified or nonverified) account...